In this study, we synthesized a biodegradable triblock copolymer poly(ethylene glycol)-poly(epsilon-caprolactone)-poly(ethylene glycol) (PEG-PCL-PEG, PECE) by ring-opening copolymerization, and nanohydroxyapatite (n-HA) powder was prepared by a hydrothermal precipitation method. The obtained n-HA was incorporated into the PECE matrix to prepare injectable thermosensitive hydrogel nanocomposites. (1)H NMR, FT-IR, XRD, DSC, and TEM were used to investigate the properties of PECE copolymer and n-HA/PECE nanocomposites. The rheological measurements for n-HA/PECE nanocomposites revealed that the gelation temperature was approximately 36 degrees C. The sol-gel-sol transition behavior and phase transition diagrams were recorded through a test tube inverting method. The results showed that n-HA/PECE nanocomposites still had thermoresponsivity like that of PECE thermosensitive hydrogel. The morphology of the nanocomposites was observed by SEM; the results showed that the nanocomposites had a 3D network structure. In addition, the effects of n-HA contents on the properties of n-HA/PECE nanocomposites are also discussed in the paper. From the results, n-HA/PECE hydrogel is believed to be promising for injectable orthopedic tissue engineering due to its good thermosensitivity and injectability.

Si has been considered as a promising alternative anode for next-generation lithium ion batteries (LIBs), but the commercial application of Si anodes is still limited due to their poor cyclability. In this paper, we propose a new strategy to enhance the long-term cyclability of Si anode by embedding nano-Si particles into a Li(+)-conductive polymer to form a Si/polymer composite with core-shell structure, in which nano-Si cores act as active Li-storage phase and the polymeric matrix serves not only as a strong buffer to accommodate the volume change, but also as a protection barrier to prevent the direct contact of Si surface with electrolyte, so as to maintain the mechanical integrity of Si anode and suppress the repeated destruction and construction of solid electrolyte interphase (SEI) on the Si surface. To realize this strategy, we synthesize a Si/PPP (polyparaphenylene) composite simply by ball-milling the Si nanoparticles with PPP polymer that has n-doping activity. Our experimental results demonstrate that the thus-prepared Si/PPP composite exhibits a high capacity of 3184 mA h g(-1) with an initial coulombic efficiency of 78%, an excellent rate capability with a considerably high capacity of 1670 mA h g(-1) even at a very high rate of 16 A g(-1), and a long-term cyclability with 60% capacity retention over 400 cycles, showing a great prospect for battery application. In addition, this structural design could be adopted to other Li-storable metals or alloys for developing cycle-stable anode materials for Li-ion batteries.

Silicon (Si) has been regarded as a promising high-capacity anode material for developing advanced lithium-ion batteries (LIBs), but the practical application of Si anodes is still unsuccessful mainly due to the insufficient cyclability. To deal with this issue, we propose a new route to construct a dual core-shell structured Si@SiO@C nanocomposite by direct pyrolysis of poly(methyl methacrylate) (PMMA) polymer on the surface of Si nanoparticles. Since the PMMA polymers can be chemically bonded on the nano-Si surface through the interaction between ester group and Si surface group, and thermally decomposed in the subsequent pyrolysis process with their alkyl chains converted to carbon and the residue oxygen recombining with Si to form SiO, the dual core-shell structure can be conveniently formed in a one-step procedure. Benefiting from the strong buffering effect of the SiO interlayer and the efficient blocking action of dense outer carbon layer in preventing electrolyte permeation, the obtained nanocomposite demonstrates a high capacity of 1972 mA h g, a stable cycling performance with a capacity retention of >1030 mA h g over 500 cycles, and particularly a superiorly high Coulombic efficiency of >99.5% upon extended cycling, exhibiting a great promise for practical uses. More importantly, the synthetic method proposed in this work is facile and low cost, making it more suitable for large-scale production of high capacity anode for advanced LIBs.

No abstract