Recently, graphene-based semiconductor photocatalysts have attracted more attention because of their enhanced photocatalytic activity caused by interfacial charge transfer (IFCT). However, the effect of a chemical bond is rarely involved for the IFCT. In this work, TiO2/graphene composites with a chemically bonded interface were prepared by a facile solvothermal method using tetrabutyl orthotitanate (TBOT) as the Ti source. The chemically bonded TiO2/graphene composites effectively enhanced their photocatalytic activity in photodegradation of formaldehyde in air, and the graphene content exhibited an obvious influence on the photocatalytic activity. The prepared composite with 2.5 wt % graphene (G2.5-TiO2) showed the highest photocatalytic activity, exceeding that of Degussa P25, as-prepared pure TiO2 nanoparticles, and the mechanically mixed TiO2/graphene (2.5 wt %) composite by a factor of 1.5, 2.6, and 2.3, respectively. The enhancement in the photocatalytic activity was attributed to the synergetic effect between graphene and TiO2 nanoparticles. Other than the graphene as an excellent electron acceptor and transporter, the enhanced photocatalytic activity was caused by IFCT through a C–Ti bond, which markedly decreased the recombination of electron–hole pairs and increased the number of holes participating in the photooxidation process, confirmed by XPS analysis, the gaseous phase transient photocurrent response, electrochemical impedance spectroscopy, and photoluminescence spectra. This work about effective IFCT through a chemically bonded interface can provide new insights for directing the design of new heterogeneous photocatalysts, which can be applied in environmental protection, water splitting, and photoelectrochemical conversion.

In this paper, thin film gas sensors made from 8-nm-diameter and exposed-{10-10}-facet ZnO nanorods selfaligning along the ceramic tube are fabricated by a simple dipcoating method. On the sensor surface, we successfully synthesize a ZnO nanorods array exposed with (0001) plane in situ by a facile solution-processing technique. Compared with the unprocessed sensor (i.e., dip-coated ZnO film based sensor), the main advantages of the solution-processed sensor are a high sensitivity (3-fold prefactor A g ), fast response (less than 10 s), and low detection limit (1 ppm) to benzene and ethanol. The enhancement in the gas-sensing performance suggests that the effect of exposed facet is dominant rather than the size effect, and the order of gas-sensing properties of ZnO crystal face is (0001) > {10-10}. On the basis of these results, it is found that the surface structure at the atomic level is a key factor in improving the oxygen adsorption and, consequently, the gas-sensing performance of a ZnO nanorods array based gas sensor.

Unique gas-sensing properties of semiconducting hybrids that are mainly related to the heterogeneous interfaces have been considerably reported. However, the effect of heterogeneous interfaces on the gas-sensing properties is still unclear, which hinders the development of semiconducting hybrids in gas-sensing applications. In this work, SnO2-SnS2 hybrids were synthesized by the oxidation of SnS2 at 300 °C with different times and exhibited high response to NH3 at room temperature. With the increasing oxidation time, the relative concentration of interfacial Sn bonds, O-Sn-S, among the total Sn species of the SnO2-SnS2 hybrids increased first and then decreased. Interestingly, it can be found that the response of SnO2-SnS2 hybrids to NH3 at room temperature exhibited a strong dependence on the interfacial bonds. With more chemical bonds at the interface, the lower interface state density and the higher charge density of SnO2 led to more chemisorbed oxygen, resulting in a high response to NH3. Our results revealed the real roles of the heterogeneous interface in gas-sensing properties of hybrids and the importance of the interfacial bonds, which offers guidance for the material design to develop hybrid-based sensors.

After the successful solvothermal synthesis of graphene (GR) from ethanol and sodium, we obtained chemically bonded graphene/BiOCl (GR/BiOCl) nanocomposite photocatalysts via a facile chemical-bath method. A significant enhancement was observed in the photodegradation of methylbenzene, which was largely ascribed to the chemical coupling effects between Bi and C, as shown by X-ray photoelectron spectroscopy. Raman spectroscopy also indicated an increased size of the sp(2) ring clusters and decreased disorder in the graphitic structure, as substitutions of defects like vacancies as well as oxygen containing carbonaceous groups with C-Bi attachment take place. Overall, information about chemical coupling effects between GR and BiOCl might take us a step further in GR-based hybrid materials, providing a very good reference to the fabrication of chemically bonded GR/semiconductor compounds and facilitating their applications in environmental protection, photo-electrochemical conversion and photocatalytic decomposition of water.

No abstract