We describe a high-resolution, high-sensitivity negative-tone photoresist technique that relies on bottom-up preassembly of differential polymer components within cylindrical polymer brush architectures that are designed to align vertically on a substrate and allow for top-down single-molecule line-width imaging. By applying cylindrical diblock brush terpolymers (DBTs) with a high degree of control over the synthetic chemistry, we achieved large areas of vertical alignment of the polymers within thin films without the need for supramolecular assembly processes, as required for linear block copolymer lithography. The specially designed chemical compositions and tuned concentric and lengthwise dimensions of the DBTs enabled high-sensitivity electron-beam lithography of patterns with widths of only a few DBTs (sub-30 nm line-width resolution). The high sensitivity of the brush polymer resists further facilitated the generation of latent images without postexposure baking, providing a practical approach for controlling acid reaction/diffusion processes in photolithography.

This work is concerned with investigating the effect of substrate hydrophobicity and zeta potential on the dynamics and kinetics of the initial stages of bacterial adhesion. For this purpose, bacterial pathogens Staphylococcus aureus and Escherichia coli O157:H7 were inoculated on the substrates coated with thin thiol layers (i.e., 1-octanethiol, 1-decanethiol, 1-octadecanethiol, 16-mercaptohexadecanoic acid, and 2-aminoethanethiol hydrochloride) with varying hydrophobicity and surface potential. The time-resolved adhesion data revealed a transformation from an exponential dependence to a square root dependence on time upon changing the substrate from hydrophobic or hydrophilic with a negative zeta potential value to hydrophilic with a negative zeta potential for both pathogens. The dewetting of extracellular polymeric substances (EPS) produced by E. coli O157:H7 was more noticeable on hydrophobic substrates, compared to that of S. aureus, which is attributed to the more amphiphilic nature of staphylococcal EPS. The interplay between the timescale of EPS dewetting and the inverse of the adhesion rate constant modulated the distribution of E. coli O157:H7 within microcolonies and the resultant microcolonial morphology on hydrophobic substrates. Observed trends in the formation of bacterial monolayers rather than multilayers and microcolonies rather than isolated and evenly spaced bacterial cells could be explained by a colloidal model considering van der Waals and electrostatic double-layer interactions only after introducing the contribution of elastic energy due to adhesion-induced deformations at intercellular and substrate-cell interfaces. The gained knowledge is significant in the context of identifying surfaces with greater risk of bacterial contamination and guiding the development of novel surfaces and coatings with superior bacterial antifouling characteristics.

No abstract

This paper describes a novel surface engineering approach that combines oxygen plasma treatment and electrochemical activation to create micropatterned cocultures on indium tin oxide (ITO) substrates. In this approach, photoresist was patterned onto an ITO substrate modified with poly (ethylene) glycol (PEG) silane. The photoresist served as a stencil during exposure of the surface to oxygen plasma. Upon incubation with collagen (I) solution and removal of the photoresist, the ITO substrate contained collagen regions surrounded by nonfouling PEG silane. Chemical analysis carried out with time-of-flight secondary ion mass spectrometry (ToF-SIMS) at different stages in micropatterned construction verified removal of PEG-silane during oxygen plasma and presence of collagen and PEG molecules on the same surface. Imaging ellipsometry and atomic force microscopy (AFM) were employed to further investigate micropatterned ITO surfaces. Biological application of this micropatterning strategy was demonstrated through selective attachment of mammalian cells on the ITO substrate. Importantly, after seeding the first cell type, the ITO surfaces could be activated by applying negative voltage (−1.4 V vs Ag/AgCl). This resulted in removal of nonfouling PEG layer and allowed to attach another cell type onto the same surface and to create micropatterned cocultures. Micropatterned cocultures of primary hepatocytes and fibroblasts created by this strategy remained functional after 9 days as verified by analysis of hepatic albumin. The novel surface engineering strategy described here may be used to pattern multiple cell types on an optically transparent and conductive substrate and is envisioned to have applications in tissue engineering and biosensing.