Aspect Ratio (AR) is one of the main design parameters of straight-bladed vertical axis turbines. This paper will examine whether a high AR, with long blades and low tip losses, or a low AR, with a higher diameter and higher losses, is more suitable to achieve the maximum power output given a fixed cross-sectional area.Traditional Double-Multiple Stream-Tube (DMST) approaches are limited by a lack of tip loss formulations specifically conceived for vertical axis turbines. Therefore, a CFD-3D investigation covering a power range from micro-generation to MW has been done. Results show that both Reynolds number and tip losses strongly influence the aerodynamic performance of the rotor. More advantages seem to be achieved by limiting tip losses rather than increasing chord-based Reynolds number (Rec), addressing towards high AR at least for medium and large-size turbines. However, as turbine size and wind speed decrease, this difference narrows considerably. For micro turbines, tip losses are balanced by the effects of Rec, thus a variation of AR does not imply a variation of CP. For all the cases that have been analysed, turbine size and therefore Rec does not appreciably affect the normalized CP distribution along the blade, which only depends on AR.

District heating networks are commonly addressed in the literature as one of the most effective solutions for decreasing the greenhouse gas emissions from the building sector. These systems require high investments which are returned through the heat sales. Due to the changed climate conditions and building renovation policies, heat demand in the future could decrease, prolonging the investment return period. The main scope of this paper is to assess the feasibility of using the heat demand -outdoor temperature function for heat demand forecast. The district of Alvalade, located in Lisbon (Portugal), was used as a case study. The district is consisted of 665 buildings that vary in both construction period and typology. Three weather scenarios (low, medium, high) and three district renovation scenarios were developed (shallow, intermediate, deep). To estimate the error, obtained heat demand values were compared with results from a dynamic heat demand model, previously developed and validated by the authors. The results showed that when only weather change is considered, the margin of error could be acceptable for some applications (the error in annual demand was lower than 20% for all weather scenarios considered). However, after introducing renovation scenarios, the error value increased up to 59.5% (depending on the weather and renovation scenarios combination considered). The value of slope coefficient increased on average within the range of 3.8% up to 8% per decade, that corresponds to the decrease in the number of heating hours of 22-139h during the heating season (depending on the combination of weather and renovation scenarios considered). On the other hand, function intercept increased for 7.8-12.7% per decade (depending on the coupled scenarios). The values suggested could be used to modify the function parameters for the scenarios considered, and improve the accuracy of heat demand estimations.

The interest in hydrokinetic conversion systems has significantly grown over the last decade with a special focus on cross-flow systems, generally known as Vertical Axis Water Turbines (VAWTs). However, analyzing of regions of interest for tidal energy extraction and outlining optimal rotor geometry is currently very computationally expensive via conventional 3D Computational Fluid Dynamics (CFD) methods. In this work, a VAWT load prediction routine developed at University of Pisa based upon the Blade Element-Momentum (BEM) theory is presented and validated against high-resolution 2D CFD simulations. Our model is able to work in two configurations, i.e. Double-Multiple Streamtube (DMST) mode, using 1D flow simplifications for quick analyses, and Hybrid mode, coupled to a CFD software for more accurate results. As a practical application, our routine is employed for a site assessment analysis of the Cape Cod area to quickly highlight oceanic regions with high hydrokinetic potential, where further higher-order and more computationally expensive CFD analyses can be performed. Ocean data are obtained from data-assimilative ocean simulations predicted by the 4D regional ocean modeling system of the Multidisciplinary Simulation, Estimation, and Assimilation Systems (MSEAS) group of the Massachusetts Institute of Technology.

A MATLAB routine, based on a Double Multiple Stream Tube model, developed to quickly predict the performance of cross-flow hydrokinetic turbine, here is presented. The routine evaluate flow data obtained with the open-source marine circulation code SHYFEM. The tool can establish the best locations to place tidal devices taking into account bathymetric constraints and the hydrokinetic potential. Hence, it can be used to decide the best set of geometrical parameters. The geometrical variables of our analysis are turbine frontal area, aspect ratio and solidity. Several sub-models, validated with 3D and 2D CFD simulations, reproduce phenomena such as dynamic stall, fluid dynamic tips losses and the lateral deviation of streamlines approaching the turbine. As a case study, the tool is applied to an area of the northern Adriatic Sea. After having identified some suitable sites to exploit the energy resource, we have compared behaviours of different turbines. The set of geometrical parameters that gives the best performance in terms of power coefficient can vary considering several locations. Conversely, the power production is always greater for turbine with low aspect ratio (for a fixed solidity and area). Indeed, shorter devices benefit from higher hydrokinetic potentials at the top of the water column.