The shipbuilding industry, engine manufacturing, aviation, rocket and space technology are promising fields of application for polymeric composite materials. Shape-generating moulding tools with internal heating are used for the creation of a more economically viable method of moulding of internally heated composite structures. The use of a fine-fibered resistive structure in the heated tools allows implementation of effective heating of the composite and elimination of the need for expensive and energy-intensive heating equipment. The aim of this paper was the reduction of energy consumption for internally heated moulding tools by choosing the optimal parameters for their resistive layer. A method for determination of the parameters of the moulding tool resistive layer was developed. This method allows calculation of the heating layer parameters and implementation of the specified time–temperature regime for moulding of the composite structure. It was shown that energy saving for the heated fiberglass shape-generating moulding tools was from 40 to 60%. It was found that the increase in the thickness of the moulded package of the polymeric composite material resulted not only in a higher supplied power for the heating system, but also in a complication of the method for system control, because of the growing exothermic effect of the binder curing reaction. For composite products based on Hysol EA 9396 binder, thicknesses more than 4 mm are critical, because it is not possible to cope with the self-heating effect only by cooling with ambient air already utilized at the twentieth minute of the moulding process. The influence of the physical and mechanical characteristics of the moulding tool material and stiffening ribs was analysed in terms of energy consumption and controllability of the heating system. Fiberglass shows the lowest energy consumption. Heating of the aluminium and steel moulding tools for the same purpose will require 20% and 45% more power, respectively. An increase in the number of stiffening ribs has a strong effect on the heat removal of the heating system. With a small number of aluminium ribs it is not possible to maintain the specified temperature–time regime for a fiberglass moulded package of 5 mm thick with the use of the equipment. However, when the number of stiffeners is increased to 10, the exothermic effect of the reaction becomes smoother and then the heating equipment can cope with the task. An experimental prototype of heating equipment of moulding tools for the manufacturing of structures of polymeric composite materials, as well as a flexible thermal blanket for repair of non-separable structures, were developed. The results can be the basis for a new method of optimal design of parameters of moulding tool structure at minimal heat removal to the environment.
The mass application of FDM technology is slowed down due to the difficulty of selecting 3D printing parameters in order to manufacture an article with the required characteristics. This paper reports a study into the impact of 3D printing parameters (temperature, print speed, layer height) on mechanical parameters (strength, elasticity module), as well as on the accuracy of printing and roughness of the surface of a specimen based on thermoplastic (PLA plastic). Several batches of specimens were fabricated for this study in accordance with ASTM D638 and ASTM D695, which were tested for tension, geometric accuracy, and roughness. Based on the experimental data, regression analysis was carried out and the functional dependences of the strength, elasticity module, printing precision, roughness of a surface on 3D printing parameters (temperature, speed, thickness of the layer) were constructed. In addition, the derived mathematical model underlying a method of non-linear programming has established such printing parameters that could provide for the required properties of a structure. The analytical dependences reported in the current work demonstrate a high enough determination factor in the examined range of parameters. Using functional dependences during the design phase makes it possible to assess the feasibility of its manufacture with the required properties, reduce the time to work out the process of printing it, and give recommendations on the technological parameters of 3D printing. The recommendations from this study could be used to make PLA-plastic articles for various purposes with the required properties
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.