No abstract

No abstract

Purpose -The purpose of this paper is to investigate the durability of radio-frequency identification (RFID) chips assembled on flexible substrates (paper and foil), with materials evaluated with regard to mechanical stresses and dependence on the applied substrate, antenna materials, chip pad printing and chip encapsulation. Design/methodology/approach -RFID chips were assembled to antennas screen printed on flexible substrates. Shear and bending tests were conducted in order to evaluate the mechanical durability of the chip joints depending on the materials used for mounting the RFID chip structures. X-ray inspection and cross sectioning were performed to verify the quality of the assembly process. The microstructure and the resistance of the materials used for chip pads were investigated with the aim of determining the conductivity mechanism in the printed layers. Findings -Addition of carbon nanotubes to the conductive adhesive (CA) provided a higher shear force for the assembled RFID chips, compared to the unmodified conductive adhesive or a polymer paste with silver flakes. However, this additive resulted in an increase in the material's resistance. It was found that the RFID substrate material had a significant influence on the shear force of mounted chips, contrary to the materials used for printing antennas. The lower shear force for chips assembled on antennas printed on paper rather than on foil was probably connected with its higher absorption of solvent from the pastes. Increasing the curing temperature and time resulted in an additional increase in the shear force for chips assembled to antennas printed on foil. A reverse dependence was observed for chips mounted on the antennas made on paper. An improvement in the durability of the RFID chip structures was achieved by chip encapsulation. Bending tests showed that a low-melting adhesive was the best candidate for encapsulation, as it provided flexibility of the assembled structure. Research limitations/implications -Further studies are necessary to investigate the mechanical durability of RFID chips assembled with a conductive adhesive, with different addition levels and types of carbon nanotubes. Practical implications -The results revealed that the best candidate for providing the highest RFID chip durability related to mechanical stresses was the low-melting adhesive. It can be recommended for practical use, as it simplified the assembly process and reduced the curing step in the encapsulation of the RFID devices. From the results of shear testing, conductive adhesives with carbon nanotubes can be used in RFID chip assembly because of their ability to increase the shear force of joints created between the antenna and the chip. Originality/value -In this paper, the influence of the materials used for antenna, chip pads, encapsulation and the curing conditions on the mechanical durability (shear and bending) of RFID chips was analyzed. Commercial and elaborated materials were compared. Some new materials containing a conductive adhesive and carbon ...

Purpose – The purpose of this paper is to determine the dependence of mechanical strength of solder joints on printed circuit boards from the soldering process parameters and operating conditions of the electronic device. Design/methodology/approach – The research was performed using the Taguchi method of planning of experiments. Evaluation of the quality of solder joints was made on the basis of microscopic observations, X-ray analysis and measurements of shear force of solder joints. Findings – The carried out research has shown the influence of the individual parameters of the soldering process on the mechanical strength of solder joints and the mechanism of damage of solder joints under the influence of shear force. Originality/value – The authors present results of their research using advanced techniques of experimental design and analysis of results. In this study, original approach was used to simulate the operational conditions of electronic devices including thermal imaging technology.

Purpose -The purpose of this paper is to investigate the thermal behaviour of thin-and thick-film resistor with different dimensions and contacts embedded into printed circuit board (PCB) and compare them to the similar constructions of discrete chip resistors assembled to standard PCBs. Design/methodology/approach -In investigations the thin-and thick-film embedded resistors with the bar form in different dimensions and configurations of contacts as well as rectangular chip resistors in package 0603 and 0402 were used. In tests were carried out the measurements of dissipated power in temperature of resistor about 408C, 708C and 1558C. The power dissipation was calculated as a multiplying of electrical current flowing through the resistor with voltage across the resistor. The dissipation of heat generated by electrical current flowing through resistors was examined by means of the FLIR A320 thermographic camera with lens Closeup £ 2 and the power source. Findings -The results show that, in case of chip resistors, the intensity of heat radiation strongly depends on dimensions of copper contact lands and also depends on the dimensions of the resistor. In case of embedded resistors, with comparable dimensions to chip resistors, they have lower ability to power dissipation, as well as the copper contact lands dimensions have lower influence. The thermal radiation through resin material is not as effective as it is in case of resistors assembled on PCB. However, the embedded thick-film resistors, especially made of paste Minico M2010, have already the similar parameters to 0402 chip resistors. Research limitations/implications -Research shows that embedded resistors can be used interchangeably with SMD resistors it allows to open up space on the surface of PCB, but it should be taken into account the lower energy dissipation capabilities. It is suggested that further studies are necessary for accurately determining the thermal effects and investigate the structures of embedded passive components that allow for better heat management. Originality/value -Thermal stability of embedded resistors during operation is a critical factor of success of embedded resistor technology. The way of power dissipation and heat resistance are one of the important operating parameters of these components. The results provide information about the power and the energy dissipation of embedded thin-and thick-film resistors compared to the standard surface mount technology.