Small-diameter biotube vascular grafts developed by in-body tissue architecture had high patency at implantation into rabbit carotid arteries or rat abdominal aortas. However, the thin walls (34 ± 14 μm) of the original biotubes made their implantation difficult into areas with low blood flow volumes or low blood pressure due to insufficient mechanical strength to maintain luminal shape. In this study, caged molds with several windows were designed to prepare more robust biotubes. The molds were assembled with silicone tubes (external diameter 2 mm) and cylindrical covers (outer diameter 7 mm) with 12 linear windows (1 × 9 mm). After the molds were embedded into beagle dorsal subcutaneous pouches for 4 weeks, type C (cage) biotubes were obtained by completely extracting the surrounding connective tissues from the molds and removing the molds. The biotube walls (778 ± 31 μm) were formed at the aperture (width 1 mm) between the silicone rods and the covers by connective cell migration through the windows of the covers. Excellent mechanical properties (external pressure resistance, approximately 4 times higher than beagle native femoral arteries; burst strength, approximately 2 times higher than original biotubes) were obtained. In the acute phase of implantation of the biotubes into beagle femoral arteries, perfect patency was obtained with little stenosis and no aneurysmal dilation. The type C biotubes may be useful for implantation into peripheral arteries or veins in addition to aortas.

Biotubes, i.e., in vivo tissue-engineered connective tubular tissues, are known to be effective as vascular replacement grafts with a diameter greater than several millimeters. However, the performance of biotubes with smaller diameters is less clear. In this study, MicroBiotubes with diameters <1 mm were prepared, and their patency was evaluated noninvasively by optical coherence tomography (OCT) and magnetic resonance angiography (MRA). MicroBiotube molds, containing seven stainless wires (diameter 0.5 mm) covered with silicone tubes (outer diameter 0.6 mm) per mold, were embedded into the dorsal subcutaneous pouches of rats. After 2 months, the molds were harvested with the surrounding capsular tissues to obtain seven MicroBiotubes (internal diameter 0.59 ± 0.015 mm, burst pressure 4190 ± 1117 mmHg). Ten-mm-long MicroBiotubes were allogenically implanted into the femoral arteries of rats by end-to-end anastomosis. Cross-sectional OCT imaging demonstrated the patency of the MicroBiotubes immediately after implantation. In a 1-month follow-up MRA, high patency (83.3 %, n = 6) was observed without stenosis, aneurysmal dilation, or elongation. Native-like vascular structure was reconstructed with completely endothelialized luminal surfaces, mesh-like elastin fiber networks, regular circumferential orientation of collagen fibers, and α-SMA-positive cells. Although the long-term patency of MicroBiotubes still needs to be confirmed, they may be useful as an alternative ultra-small-caliber vascular substitute.

No abstract

Variations in microscopic elastic structures along the entire length of canine aorta were evaluated by use of a scanning haptic microscope (SHM). The total aorta from the aortic arch to the abdominal aorta was divided into 6 approximately equal segments. After embedding the aorta in agar, it was cut into horizontal circumferential segments to obtain disk-like agar portions containing ring-like samples of aorta with flat surfaces (thickness, approximately 1 mm). The elastic modulus and topography of the samples under no-load conditions were simultaneously measured along the entire thickness of the wall by SHM by using a probe with a diameter of 5 μm and a spatial resolution of 2 μm at a rate of 0.3 s/point. The elastic modulus of the wall was the highest on the side of the luminal surface and decreased gradually toward the adventitial side. This tendency was similar to that of the change in the elastin fiber content. During the evaluation of the mid-portion of each tunica media segment, the highest elastic modulus (40.8 ± 3.5 kPa) was identified at the thoracic section of the aorta that had the highest density of elastic fibers. Under no-load conditions, portions of the aorta with high elastin density have a high elastic modulus.