No abstract

Collagen type I, commonly derived from xenogenic sources, is extensively used as a biomaterial for tissue engineering applications. However, the use of xenogenic collagen is typically associated with species specific variation in mechanical, structural, and biological properties that are known to influence cellular response and remodeling. In addition, immunological complications and risks of disease transmission are also major concerns. The goal of this study is to characterize a new xeno-free human skin-derived collagen and assess its applicability as a bioink for cell-laden 3 D bioprinting. Four different concentrations of human collagen (i.e., 0.5 mg/mL, 1 mg/mL, 3 mg/mL and 6 mg/mL) were employed for the synthesis of collagen hydrogels. In addition, bovine collagen was used as a xenogenic control. Results from SDS-PAGE analysis showed the presence of α1, α2, and β chains, confirming that the integrity of type I human collagen is maintained post isolation. Polymerization rate and compressive modulus increased significantly with increase in the concentration of human collagen. When comparing two different sources of collagen, the polymerization rate of xenogenic collagen was significantly faster (p < 0.05) than human collagen while the compressive modulus was comparable. Raman spectroscopy showed a large peak in the Amide I band around 1600 cm−1, indicating a dense and supraorganized fibrillar structure in human collagen hydrogels. Conversely, Amide I band intensity for xenogenic collagen was comparable to that of Amide II and Amide III bands. Further, the use of 6 mg/mL human collagen as a bioink yielded 3 D printed constructs with high shape fidelity and cell viability. On the other hand, xenogenic collagen failed to yield stable 3 D printed constructs. Together, the results from this study provides an impetus for using human-derived collagen as a viable alternative to xenogenic sources for 3 D bioprinting of clinically relevant scaffolds for tissue engineering applications.

Bioactive three-dimensional (3D) printed scaffolds are promising candidates for bone tissue engineering (BTE) applications. Here, we introduce a bioactive ink composed of Bioglass 45S5 (BG) and methacrylated collagen (CMA) for 3D printing of biomimetic constructs that resemble the organic and inorganic composition of native bone tissue. A uniform dispersion of BG particles within the collagen network improved stability and reduced swelling of collagen hydrogels. Rheological testing showed significant improvement in the yield stress and percent recovery of 3D printed constructs upon BG incorporation. Further, addition of BG improved the bone bioactivity of 3D printed constructs in stimulated body fluid. BG incorporated CMA (BG-CMA) constructs maintained high cell viability and enhanced alkaline phosphatase activity of human mesenchymal stem cells. In addition, cell-mediated calcium deposition was significantly higher on BG-CMA constructs, compared to CMA alone. In conclusion, 3D printed BG-CMA constructs have significant potential for use in BTE applications.

No abstract

Chronic wounds affect over 400,000 people in the United States alone, with up to 60,000 deaths each year from non-healing ulcerations. Tissue grafting (e.g., autografts, allografts, and xenografts) and synthetic skin substitutes are common treatment methods, but most solutions are limited to symptomatic treatment and do not address the underlying causes of the chronic wound. Use of fat grafts for wound healing applications has demonstrated promise but these grafts suffer from low cell viability and poor retention at the wound site resulting in suboptimal healing of chronic wounds. Herein, we report on an innovative closed-loop fat processing system (MiniTCTM) that can efficiently process lipoaspirates into microfat clusters comprising of highly viable regenerative cell population (i.e., adipose stromal cells, endothelial progenitors) preserved in their native niche. Cryopreservation of MiniTCTM isolated microfat retained cell count and viability. To improve microfat retention and engraftment at the wound site, microfat was mixed with methacrylated collagen (CMA) bioink and 3D printed to generate microfat-laden collagen constructs. Modulating the concentration of microfat in CMA constructs had no effect on print fidelity or stability of the printed constructs. Results from the Alamar blue assay showed that the cells remain viable and metabolically active in microfat-laden collagen constructs for up to 10 days in vitro. Further, quantitative assessment of cell culture medium over time using ELISA revealed a temporal expression of proinflammatory and anti-inflammatory cytokines indicative of wound healing microenvironment progression. Together, these results demonstrate that 3D bioprinting of microfat-laden collagen constructs is a promising approach to generate viable microfat grafts for potential use in treatment of non-healing chronic wounds.