Chitosan is one of prospective polymer for use in regenerative medicine which has unique properties such as biocompatibility, biodegradability, antimicrobial, antiinflammatory, and antitumor potency. In this article, we study the peculiarities of the surface modification of chitosan films with carbonyl-containing compounds, which differed both in molecular characteristics and in their hydrophilic and hydrophobic properties. The potential for controlling the biodegradation of the resulting materials has been established, which can be used in the creation of wound dressings. Both the destruction time and lyophilic properties of the surface depend on the length of the modifier's hydrocarbon radical. The contact angle and water absorption of obtained film materials correlate with hydrophobicity, which estimated by the calculated value of the hydrophilic-lipophilic balance (HLB). The 2 cytotoxicity of modified chitosan films was studied, and it was found that they are non-toxic (cytotoxic index of <50%) for human skin cell cultures, which shows their potential for use in the creation of materials for skin protection and external wound healing.

Chitosan is one of promising polymer from natural polysaccharides, which is an environmentally friendly compound from renewable raw materials. Chitosan has biodegradability, biocompatibility, and exhibits antimicrobial, antibacterial, and other activities. In this article, we report the rst use of copolymers based on glycidyl methacrylate and ( uoro)alkyl methacrylates as material surface wettability modi ers based on a chitosan, and we show that grafting of copolymers allows an increase in the hydrophobicity of lms with contact angles up to 114° and up to 154° for aerogels. The resulting chitosan aerogels have high porosity with a pore size of 100-200 µm and the pore walls are 0.6-0.7 µm-thick lm formations. Our study of lyophilic properties of modi ed chitosan substrates showed a change in the hydrophobicity of the materials as a function of length of the hydrocarbon radical in the side groups of ( uoro)alkyl methacrylates in the copolymers. Additionally, the rate of biodegradation of the resulting materials decreased with an increase in the number of hydrophobic groups in the modi er. Obtained chitosan materials with hydrophobic coatings have potential as a protective layer for wound dressings with an extended service life.

This paper discusses the influence of the structure of copolymers based on glycidyl methacrylate and alkyl methacrylates with C6–C18 hydrocarbon side groups on the wettability and sorption properties of surface-modified chitosan aerogels. The grafting of copolymers onto the surface of aerogels was confirmed by elemental analysis, X-ray photoelectron spectroscopy, and Fourier-transform infrared spectroscopy. As a result of the modification, with an increase in the amount of the hydrocarbon substituent alkyl methacrylate, the surface of the resulting materials became hydrophobic with contact angles in the range of 146–157°. At the same time, the water absorption of the aerogels decreased by a factor of 30 compared to that for unmodified aerogels, while the sorption capacity for light oil, diesel fuel, and synthetic motor oil remained at the level of more than 30 g/g. Chitosan aerogels with grafted copolymers based on glycidyl methacrylate and alkyl methacrylates retain biodegradation capacity; however, compared to unmodified chitosan, this process has an induction period.

The features of the modification of acid-soluble chitosan by carbonyl-containing compounds in solution and by the method of surface modification of molded materials are investigated. The dependence of the rheological properties of polysaccharide solutions on the structure of the hydrocarbon radical of the modifier is established. The formed films based on iminochitosans, obtained by the interaction of the polymer with aldehydes in a solution of acetic acid, have lower surface, hydrophobic, and strength characteristics compared to chitosan films. The possibility of biodegradation of the obtained materials, as well as the dependence of the mass loss of the samples on the HLB level, which can be used to create wound dressings with programmed degradation, is shown.

Chitosan is one of promising polymer from natural polysaccharides, which is an environmentally friendly compound from renewable raw materials. Chitosan has biodegradability, biocompatibility, and exhibits antimicrobial, antibacterial, and other activities. In this article, we report the first use of copolymers based on glycidyl methacrylate and (fluoro)alkyl methacrylates as material surface wettability modifiers based on a chitosan, and we show that grafting of copolymers allows an increase in the hydrophobicity of films with contact angles up to 114° and up to 154° for aerogels. The resulting chitosan aerogels have high porosity with a pore size of 100–200 µm and the pore walls are 0.6–0.7 µm-thick film formations. Our study of lyophilic properties of modified chitosan substrates showed a change in the hydrophobicity of the materials as a function of length of the hydrocarbon radical in the side groups of (fluoro)alkyl methacrylates in the copolymers. Additionally, the rate of biodegradation of the resulting materials decreased with an increase in the number of hydrophobic groups in the modifier. Obtained chitosan materials with hydrophobic coatings have potential as a protective layer for wound dressings with an extended service life.