No abstract

Numerous phenomena that occur during the process of machine parts’ regeneration have a significant impact on the loss of their working ability. Therefore, the properties of the working surfaces of the teeth flanks of repaired gears were analyzed in this research. The hereditary properties of the gear teeth are expressed by the interdependence of their geometric and physical-mechanical-metallurgical parameters created during the technological operations of regeneration of worn teeth by welding/hard-facing. The hard-facing was executed with three filler metal types, namely: combination Inox 18/8/6 + EDur 600, Castolin 2 and UTP 670. The tested properties included geometrical accuracy, microstructure and microhardness. Evaluation of the executed regeneration procedures was done by comparing the mentioned parameters of the regenerated gears and the new ones. The tested gears were not withdrawn from production due to damage, but they were newly manufactured and intentionally damaged gears, made of the same materials, subjected to the same manufacturing process. In this way, all influences except for the considered filler metal type were eliminated. Based on results of the conducted experiments, it was possible to establish the influence of the filler metal type on the surface characteristics of the regenerated gears’ teeth flanks.

No abstract

Steel structures are designed to operate in an elastic domain, but sometimes plastic strains induce damage and fracture. Besides experimental investigation, a phase-field damage model (PFDM) emerged as a cutting-edge simulation technique for predicting damage evolution. In this paper, a von Mises metal plasticity model is modified and a coupling with PFDM is improved to simulate ductile behavior of metallic materials with or without constant stress plateau after yielding occurs. The proposed improvements are: (1) new coupling variable activated after the critical equivalent plastic strain is reached; (2) two-stage yield function consisting of perfect plasticity and extended Simo-type hardening functions. The uniaxial tension tests are conducted for verification purposes and identifying the material parameters. The staggered iterative scheme, multiplicative decomposition of the deformation gradient, and logarithmic natural strain measure are employed for the implementation into finite element method (FEM) software. The coupling is verified by the ‘one element’ example. The excellent qualitative and quantitative overlapping of the force-displacement response of experimental and simulation results is recorded. The practical significances of the proposed PFDM are a better insight into the simulation of damage evolution in steel structures, and an easy extension of existing the von Mises plasticity model coupled to damage phase-field.

Steel of the mild-strength S355J2+N steel grade is the most often used steel for manufacturing carrying sections of constructions exposed to fatigue loads. The use of high-strength steels, such as S690QL, allows for the creation of structures that are light and simple to construct. However, increasing the yield strength of high-strength steels does not result in a corresponding increase in fatigue resistance. As a result, using high-strength steels for constructions subjected to fatigue loading can be a major design concern, raising the question of whether high-strength steels should be used at all. Most of the experimental investigations regarding the hot work tool steel X37CrMoV5-1 found in the literature are focused on its machining and wear resistance, with insufficient attention paid to the cyclic loads. This article evaluates the fatigue properties of mild-strength S355J2+N, high-strength S690QL, and X37CrMoV5-1 steel grades. A SHIMADZU servo-hydraulic testing machine is used to perform uniaxial tensile tests under uniaxial fatigue stress-controlled, fully reversed conditions (tensile–compression testing with R = −1 stress ratio) in accordance with EN ISO and ASTM standards. The aim of this paper is to highlight the fatigue characteristics of these three steels that are among the most used in their respective groups. Steel S355J2+N belongs to the group of hot-rolled normalized steels, S690QL belongs to the group of improved (quenched + tempered) steels with increased strength, and X37CrMoV5-1 belongs to the group of high-alloyed tool steels for hot work. This choice was made as the tested steels can be considered typical representatives of their groups. Based on the test results of these three steels, which are organized in S–N curves, the fatigue behavior of the entire mentioned groups of steels can be foreseen.