Similar to jet engine development, modern design methods are used today to improve the performance of industrial compressors. In order to verify the loading limits, a cascade profile representative for the first rotor hub section of an industrial compressor has been designed by optimizing the suction surface velocity distribution using a direct boundary layer calculation method. The blade shape was computed with an inverse full potential code and the resulting cascade was tested in a cascade wind tunnel. The experimental results confirmed the design intent and resulted in a low loss coefficient of 1.8 percent at design condition and an incidence range of nearly 12 deg (4 percent loss level) at an inlet Mach number of 0.62.

An experimental and numerical study of the transonic flow through a linear compressor cascade with endwalls was conducted. The cascade with a low aspect ratio of 1.34 was tested at an inlet Mach number of 1.09 and a Reynolds number of 1.9×106. Detailed flow visualizations on the surfaces and five-hole probe measurements inside the blading and in the wake region showed clearly a three-dimensional boundary layer separation on the blade surface and the sidewall, and a severe corner stall induced by a strong 3-D shock system at blade passage entrance. The experimental data have been used to validate and improve the 3-D Navier-Stokes code TRACE. Results showed an excellent resolution of the complex flow field. Surface pressure distributions on the entire blade surface and the endwalls, flow angle and total pressure contours within the blade passage and the wake are compared with the experimental results. An analysis of the secondary flow of this highly staggered cascade did not show the classical corner vortex. Instead, a severe flow deviation and partly reverse flow near the walls is seen. The flow solver helped to identify a weak ring vortex that originates from the passage sidewall. Surface oil flow pictures on the blade contour and the sidewall are in qualitatively good agreement to numerical surface streaklines. A considerable improvement of the numerical results could be achieved by a gradual grid refinement, especially in the corner region and by successive code development.

Modern methods for axial compressor design are capable of shaping the blade surfaces in a three-dimensional way. Linking these methods with automated optimization techniques provides a major benefit to the design process. The application of nonaxisymmetric contoured endwalls is considered to be very successful in turbine rotors and vanes. Concerning axial compressors, nonaxisymmetric endwalls are still a field of research. This two-part paper presents the recent development of a novel endwall design. A vortex created by a nonaxisymmetric endwall groove acts as an aerodynamic separator, preventing the passage vortex from interacting with the suction side boundary layer. This major impact on the secondary flow results in a significant loss reduction by means of load redistribution, reduction in recirculation areas, and suppressed corner separation. Part I of this paper deals with the endwall design and its compressor application. The resulting flow phenomena and physics are described and analyzed in detail. The second paper presents the detailed experimental and numerical investigation of the developed endwall groove. The measurements carried out at the transonic cascade wind tunnel of DLR in Cologne, demonstrated a considerable influence on the cascade performance. A loss reduction and redistribution of the cascade loading were achieved at the aerodynamic design point, as well as near the stall condition of the cascade. This behavior is well predicted by the numerical simulation. The combined analysis of experimental and numerical flow patterns allows a detailed interpretation and description of the resulting flow phenomena. In this context, high fidelity 3D-Reynolds-averaged Navier–Stokes flow simulations are required to analyze the complex blade and endwall boundary layer interaction.

An experimental and analytical study has been performed on the effect of Reynolds number and free-stream turbulence on boundary layer transition location on the suction surface of a controlled diffusion airfoil (CDA). The experiments were conducted in a rectilinear cascade facility at Reynolds numbers between 0.7 and 3.0×106 and turbulence intensities from about 0.7 to 4%. An oil streak technique and liquid crystal coatings were used to visualize the boundary layer state. For small turbulence levels and all Reynolds numbers tested the accelerated front portion of the blade is laminar and transition occurs within a laminar separation bubble shortly after the maximum velocity near 35–40% of chord. For high turbulence levels (Tu > 3%) and high Reynolds numbers transition propagates upstream into the accelerated front portion of the CDA blade. For those conditions, the sensitivity to surface roughness increases considerably and at Tu = 4% bypass transition is observed near 7–10% of chord. Experimental results are compared to theoretical predictions using the transition model which is implemented in the MISES code of Youngren and Drela. Overall the results indicate that early bypass transition at high turbulence levels must alter the profile velocity distribution for compressor blades that are designed and optimized for high Reynolds numbers.

An experimental and numerical study of the transonic flow through a linear compressor cascade with endwalls was conducted. The cascade with a low aspect ratio of 1.34 was tested at an inlet Mach number of 1.09 and a Reynolds number of 1.9×106. Detailed flow visualizations on the surfaces and 5-hole probe measurements inside the blading and in the wake region showed clearly a 3-dimensional boundary layer separation on the blade surface and the sidewall, and a severe corner stall induced by a strong 3D shock system at blade passage entrance. The experimental data has been used to validate and improve the 3D Navier-Stokes code TRACE. Results showed an excellent resolution of the complex flow field. Surface pressure distributions on the entire blade surface and the endwalls, flow angle and total pressure contours within the blade passage and the wake are compared with the experimental results. An analysis of the secondary flow of this highly staggered cascade did not show the classical corner vortex. Instead, a severe flow deviation and partly reverse flow near the walls is seen. The flow solver helped to identify a weak ring vortex that originates from the passage sidewall. Surface oil flow pictures on the blade contour and the sidewall are in qualitatively good agreement to numerical surface streaklines. A considerable improvement of the numerical results could be achieved by a gradual grid refinement especially in the corner region and by successive code development.