In light of environmental concerns, the textile industry has accelerated efforts to reduce or eliminate water consumption in all areas of yarn preparation, dyeing, and finishing. Supercritical fluid dyeing technology has the potential to accomplish this objective in many commercial textile applications around the world, both at present and in the future around the world. Increased interest in this technology has made a fundamental understanding of thermophysical (equilibrium solubility) and transport (kinetics) properties of such fluids and fluid mixtures necessary. Supercritical carbon dioxide (SC-CO2) is one of the most environmentally acceptable solvents in use today, and textile processes using it have many advantages when compared to conventional aqueous processes. − Positive environmental effects range from drastically reduced water consumption to eliminating hazardous industrial effluent. Furthermore, economic benefits include increased productivity and energy savings. Successfully commercializing supercritical fluid CO2 processing will improve the economics of dyeing and other textile chemical processes by eliminating water usage and wastewater discharges and increasing productivity by reducing processing times as well as required chemicals and auxiliaries and reducing energy consumption and air emissions. As a result, SC-CO2 processing will be more rapid, more economical, and more environmentally friendly.

No abstract

The presented paper reports on the development of eco-friendly non-silicone containing release liners on plastic foils for pressure sensitive adhesive tapes. A solvent free process based on aerosol assisted dielectric barrier discharge (DBD) plasma deposition was used to obtain nano-sized coatings. Various precursors have been investigated ranging from hydrocarbons and fluorinated hydrocarbons to (meth)acrylates and fluorinated (meth)acrylates. Best results were obtained using 2-ethylhexyl acrylate. To improved the stability of release properties upon ageing, addition of photo initiators and acrylic cross-linkers have been evaluated. Tape adhesion tests showed stable release values below 25 cN/20 mm for 2-ethylhexyl acrylate plasma coatings with acrylic cross-linkers.

No abstract

In a data center, electronic equipment such as server and switches dissipate heat and the corresponding cooling systems contribute to typically 25–35% of total energy consumption. The heat load continues to increase as there is a greater need for miniaturization and convergence. In 2014, data centers in the U.S. consumed an estimated 70 billion kWh, representing about 1.8% of total U.S. electricity consumption. Based on current trend estimates, U.S. data centers are projected to consume approximately 73 billion kWh in 2020 [1]. Many research and strategies are adopted to minimize energy cost. The recommended dry bulb temperature for long-term operation and reliability for air cooling is between 18–27°C and the largest allowable inlet temperature range to operate at is between 5°C and 45°C with American Society of Heating, Refrigeration, and Air-Conditioning Engineers (ASHRAE) enabling much broader allowable zones) [2]. But understanding a proper cooling system is very important especially for thermal management of IT equipment with high heat loads such as 1U or 2U multi-core, high-end servers and blade servers which provide more computing per watt. Many problems like high inlet temperature due to the mixing of hot air with cold air, local hot spots, lower system reliability, increased failure, and downtime may occur. Among many other approaches to managing high-density racks, in-row coolers are used in between racks to provide cold air and minimize local hot spots. This paper describes a computational study being performed by applying in-row coolers for different rack power configuration with and without aisle containment. The power, as well as the number of racks, are varied to study the effect of raised inlet temperature for the IT equipment in a Computational Fluid Dynamics (CFD) model developed in 6SigmaRoom with the help of built-in library items. A comparative analysis is also performed for a typical small-sized non-raised facility to investigate the efficacy and limitations of in-row coolers in thermal management of IT equipment with variation in rack heat load and containment. Several other aspects like a parametric study of variable opening areas of duct between racks and in-row coolers, the variation of operating flow rate and failure scenarios are also studied to find proper flow distribution, uniformity of outlet temperature and predict better performance, energy savings and reliability. The results are presented for general guidance for flexible and quick installation and safe operation of in-row coolers to improve thermal efficiency.