Nowadays, the incorporation of natural fiber, such as coir fiber, to high-strength concrete has sparked a lot of attention in the construction materials industry. This is because coir fibers are significantly cheaper and more widely accessible than synthetic fibers. Natural fibers such as bamboo, flax, hemp, and coir have distinct microstructures and chemical compositions from cement-based materials. The physical and mechanical properties of natural fiber, such as coir fiber, are significantly correlated with fiber concentration and cellulose component. However, coir fiber has high stretching to failure, while bamboo, flax, and hemp fibers are very resistant to stress and increase stiffness. Based on these distinctive fiber qualities, it is anticipated that coir fiber would facilitate the development of cement-based materials for advanced concrete building applications. In this paper, coir fiber-reinforced cement-based concretes were evaluated in terms of workability, compressive strength, flexural strength, splitting tensile strength, modulus of elasticity, and permeability. The relationship between strength and fiber content was analyzed to understand the impact of coir fiber on the properties of coir fiber-reinforced cement-based concrete. Based on the results obtained, it is determined that 2% coir fiber modification offers the highest compressive strength, splitting tensile strength, and flexural strength. Moreover, the modulus of elasticity is increased, and the permeability is plummeted by the volume fractions of coir fiber 1%, 2%, and 3% because the blending of coir fiber has a bridging and dispersing mechanism of the force-carrying capacity in concrete. In conclusion, coir fiber might be a viable choice for improving the strength and durability of concrete. Therefore, the sparing use of coir fiber presented in this research can be implemented for the manufacturing of concrete in the future.

The extensive use of Portland cement (PC) in the manufacturing of concrete is responsible for the depletion of natural resources that are part of cement production. Cement supply is permanently threatened by the ongoing depletion of natural materials, including sand, limestone, and clay. Concurrently, the incineration of agricultural residues presents a significant ecological problem. This study explores the substitution of cement in concrete with 5%, 10%, 15%, and 20% wheat straw ash as an environmentally friendly alternative. The purpose of this investigation is to evaluate the effect of substituting wheat straw ash (WSA) for PC on the mechanical characteristics of concrete. A total of 75 concrete samples were made by cement or cement + WSA/fine aggregate/coarse aggregate ratio of 1:1, 5:3, and water-to-cement ratio was kept constant at 0.50. All of these specimens were cured and tested at 28 days. The properties tested in the paper were workability, compressive strength, splitting tensile strength, flexural strength, modulus of elasticity, and permeability. The outcomes showed that the substitution of PC with WSA 10% resulted in the greatest concrete strength. In contrast, the mechanical properties and permeability of concrete were reduced when 20% WSA was substituted for PC at 28 days. In addition, the slump value dropped as increasing the content of WSA diminished the weight of PC in the concrete. This could be attributed to the fact that the water content in the WSA 20% concrete was not enough for mechanical strength. Other concretes with WSA showed similar properties to those of the WSA 10% concrete. It was concluded from the results that since the WSA 10% concrete showed the best properties, it can be recommended as the best recipe in this research work.

The transformation of conventional binder and grout into high-performance nanocarbon binder and grout was evaluated in this investigation. The high-performance nanocarbon grout consisted of grey cement, white cement, lime, gypsum, sand, water, and graphite nanoplatelet (GNP), while conventional mortar is prepared with water, binder, and fine aggregate. The investigated properties included unconfined compressive strength (UCS), bending strength, ultrasound pulse analysis (UPA), and Schmidt surface hardness. The results indicated that the inclusion of nanocarbon led to an increase in the initial and long-term strengths by 14% and 23%, respectively. The same trend was observed in the nanocarbon binder mortars with white cement, lime, and gypsum in terms of the UCS, bending strength, UPA, and Schmidt surface hardness. The incorporation of nanocarbon into ordinary cement produced a high-performance nanocarbon binder mortar, which increased the strength to 42.5 N, in comparison to the 32.5 N of the ordinary cement, at 28 days.

Green building materials are an alternative to ordinary materialsoffering multiple environmental benefits. This study consists of an experimental investigation of a new design of gypsum plaster blocks. First, a mix design of gypsum plaster and water mixture was prepared. The optimal mix composition was determined according to the mechanical and physical properties, such as the water absorption, the temperature of hydration, the density, and the compressive strength of different gypsum plaster and water mixtures made by varying the water dosage. The second part of this investigation aims to study a new design of green blocks prepared from the optimal water and gypsum plaster mixture. The new blocks are perforated to lighten them and to reduce their thermal conductivity in order to make them moreinsulate. Experimental tests were conducted on the block prototype, such as the measurement of dimensional tolerances, compressive strength, density, flatness, water absorption, residual moisture, surface hardness, and thermal conductivity. Experimental test results show that the new blocks have very low density, and their compressive strength is sufficient for wall construction. In addition, the manufacturing process of the new blocks is very easy and very fast. Finally, the obtained physical and mechanical properties of the new gypsum plaster blocks give it the opportunity to be used for interior walls for building constructions.

This study aims to investigate a new shear reinforcement method which utilizes thin mild steel (TMS) plates as shear reinforcement in deep beams to replace conventional reinforcement. Thirteen reinforced concrete deep beam specimens with three different plate thicknesses and four varying perforated hole arrangements on the TMS plates were experimentally tested to determine the load-carrying capacity and crack pattern. The experimental results indicate that the 2.0 mm thick TMS plate has the highest load-carrying capacity. Among the four different hole arrangements on the TMS plates, the perforated plates with a three-column hole arrangement show the best performance in terms of load-carrying capacity, with a 2.9% increment against the control beam specimen. The specimens also demonstrated compatible elastic stiffness with the control beam that used conventional shear links. This shows that TMS plates have the potential to replace conventional shear links in deep beams. This proposed method also changed the failure mode from conventional diagonal shear tension failure to a combination of flexural failure and shear deformation. A numerical model was developed and was found to have a good correlation with the experimental results, demonstrating potential for use in future parametric investigations on deep beams and cost reduction in future experimental work.