Six-port technology has been widely used in microwave systems, such as interferometric passive imaging. In this paper, an integrated Ka-band (32–36 GHz) six-port chip based on the 0.15-μm GaAs technology is designed and fabricated to simplify the circuit structure and miniaturize the volume of the imaging system. The designed chip integrates two amplifiers, two phase shifters, and a six-port circuit as part of an analog complex correlator. In this integrated chip, the crosstalk between the two amplifiers cannot be ignored. This paper analyzes the influence of the isolation between two amplifiers on the correlation results to guide the six-port chip design. In addition, considering that the radiometer system receives a broadband noise signal, the phase shifter needs to ensure that the phase shift range of each frequency point is the same under the same control conditions. Therefore, the phase shifter is designed with a high-pass and low-pass structure. The measurement results show that the isolation between the two amplifiers is greater than 20 dB, and the measured phase shift range and phase shift range error of the designed chip are 220° and 10°, respectively, with the control voltage varying from 0 to 1.5 V, which meets the requirements of the system.

The design, analysis, implementation and measurement of an integrated V-band receiver front-end based on 0.15 μm GaAs pHEMT process are presented in this paper. The front-end chip uses the super-heterodyne topology which consists of a low noise amplifier, an image reject mixer, and a multiplyby-four (×4) LO chain. In order to minimize the power consumed by LO chain, an active single-ended mixer is designed which requires extremely low LO power of -5 dBm. Meanwhile, the effect of signal coupling in the integrated chip is analyzed and solutions are proposed. By introducing appropriate filters into the circuit and optimizing the overall layout, the imbalance of in-phase and quadrature signals caused by unwanted coupling can be effectively mitigated, thus enhancing the image rejection of the chip. Probe and module tests are applied to the receiver front-end, and the measurement results reveal that the chip achieves -3 ± 0.7 dB conversion gain, 7 dB noise figure and more than 25 dB image rejection ratio in the RF frequency range of 52-56 GHz. Only one supply voltage of 3 V is required for the chip, and total power consumption is 312 mW. Moreover, with a continuously adjustable phase control of 360° and very broadband IF characteristics, the front-end chip is suitable for passive millimeter-wave imaging applications.INDEX TERMS Integrated receiver front-end, V-band, low LO power, high image rejection, 0.15 μm GaAs pHEMT, passive millimeter-wave imaging.

In this paper, the design, fabrication, and measurement of a compact broadband (4–8 GHz) analog complex correlator for a passive millimeter-wave imaging system are presented. To achieve high sensitivity and high integration of the imaging system, the wideband and miniaturization of the correlator are required. The correlator achieves wide bandwidth by using the add-and-square method, which is composed of a six-port circuit and a detection circuit. In order to realize the miniaturization of the correlator, the six-port circuit is realized on the chip base on the 0.15-μm gallium arsenide (GaAs) process. The influence of mismatch of the detection circuit that employs zero-bias Schottky diodes on the correlator is also analyzed to guide the design of the correlator. The measurement results of the designed chips and detector are consistent with the simulation result. Finally, a Sweep-frequency test is applied to the designed correlator, and the measurement results show that, within the frequency range of 4–8 GHz, the correlation amplitude fluctuation is less than 1.9 dB and the correlation efficiency is larger than 99%, which reveal that the correlator is suited for interferometric passive millimeter-wave imaging applications.

This paper presents a Ka band eight-channel integrated packaged phased array receiver front-end for a passive millimeter-wave imaging system. Since multiple receiving channels are integrated in a given package, the mutual coupling issue affecting the channel will deteriorate imaging quality. Therefore, in this study, the influence of channel mutual coupling on the system array pattern and amplitude phase error is analyzed, and the design requirements are proposed according to the results. During the design implementation, the coupling paths are discussed, and passive circuits in the path are modeled and designed to reduce the level of channel mutual coupling and spatial radiation. Finally, an accurate coupling measurement method for a multi-channel integrated phased array receiver is proposed. The receiver front-end achieves a 28~31 dB single channel gain, a 3.6 dB noise figure, less than −47 dB of channel mutual coupling. Furthermore, the array pattern of the two-dimensional 1024 channel system composed of the front end of the receiver is consistent with the simulation, and the receiver’s performance is verified by a human-body-imaging experiment. The proposed coupling analysis, design, and measurement methods are also applicable to other multi-channel integrated packaged devices.

Human body temperature is a fundamental physiological sign that reflects the state of physical health. It is important to achieve high-accuracy detection for non-contact human body temperature measurement. In this article, a Ka band (32 to 36 GHz) analog complex correlator using the integrated six-port chip is proposed, and a millimeter-wave thermometer system based on the designed correlator is completed for human body temperature measurement. The designed correlator utilizes the six-port technique to achieve large bandwidth and high sensitivity, and miniaturization of the correlator is achieved through an integrated six-port chip. By performing the single-frequency test and the broadband noise measurement on the correlator, we can determine that the dynamic range of input power of the correlator is −70 dBm to −35 dBm, and the correlation efficiency and equivalent bandwidth are 92.5% and 3.42 GHz, respectively. Moreover, the output of the correlator varies linearly with the input noise power, which reveals that the designed correlator is suitable for the field of human body temperature measurement. Then, a handheld thermometer system, with a size of 140 mm × 47 mm × 20 mm, is proposed using the designed correlator, and the measurement results show that the temperature sensitivity of the thermometer is less than 0.2 K.