In order to obtain homogeneous dispersion and strong filler-matrix interface in epoxy resin, graphene oxide was functionalized via surface modification by hexachlorocyclotriphosphazene and glycidol and then incorporated into epoxy resin to obtain nanocomposites via in situ thermal polymerization. The morphology of nanocomposites was characterized by scanning electron microscopy and transmission electron microscopy, implying good dispersion of graphene nano-sheets. The incorporation of functionalized graphene oxide effectively enhanced various property performances of epoxy nanocomposites. The storage modulus of the epoxy nanocomposites was significantly increased by 113% (2% addition) and the hardness was improved by 38% (4% addition). Electrical conductivity was improved by 6.5 orders of magnitude. Enhanced thermal stability was also achieved. This work demonstrates a cost-effective approach to construct a flexible interphase structure, strong interfacial interaction and good dispersion of functionalized graphene in epoxy nanocomposites through a local epoxy-rich environment around graphene oxide sheets, which reinforces the polymer properties and indicates further application in research and industrial areas.

A series of sodium alginate (SA) nanocomposite films with different loading levels of graphitic-like carbon nitride (g-C3N4) were fabricated via the casting technique. The structure and morphology of nanocomposite films were investigated by X-ray powder diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, and transmission electron microscopy. Thermogravimetric analysis results suggested that thermal stability of all the nanocomposite films was enhanced significantly, including initial thermal degradation temperature increased by 29.1 °C and half thermal degradation temperature improved by 118.2 °C. Mechanical properties characterized by tensile testing and dynamic mechanical analysis measurements were also reinforced remarkably. With addition of 6.0 wt % g-C3N4, the tensile strength of SA nanocomposite films was dramatically enhanced by 103%, while the Young's modulus remarkably increased from 60 to 3540 MPa. Moreover, the storage modulus significantly improved by 34.5% was observed at loadings as low as 2.0 wt %. These enhancements were further investigated by means of differential scanning calorimetry and real time Fourier transform infrared spectra. A new perspective of balance was proposed to explain the improvement of those properties for the first time. At lower than 1.0 wt % loading, most of the g-C3N4 nanosheets were discrete in the SA matrix, resulting in improved thermal stability and mechanical properties; above 1.0 wt % and below 6.0 wt % content, the aggregation was present in SA host coupled with insufficient hydrogen bondings limiting the barrier for heat and leading to the earlier degradation and poor dispersion; at 6.0 wt % addition, the favorable balance was established with enhanced thermal and mechanical performances. However, the balance point of 2.0 wt % from dynamic mechanical analysis was due to combination of temperature and agglomeration. The work may contribute to a potential research approach for other nanocomposites.

No abstract

A novel phosphorus- and nitrogen-containing compound (POPHA) has been synthesized by allowing phosphorus oxychloride to react with piperazine and 2-hydroxyethyl acrylate (HEA). Its structure was characterized by FTIR, 1H NMR, and 31P NMR. A series of UV-curable flame-retardant resins were obtained by blending POPHA with EA in different ratios. The flame-retardant properties were characterized by the limiting oxygen index (LOI) and microscale combustion calorimeter (MCC). The results showed that the incorporation of POPHA into EA can improve the flame retardancy of EA dramatically. The thermal properties of the resins were investigated by thermogravimetric analysis (TGA) in air atmosphere. Moreover, the thermal degradation mechanisms of the EA/POPHA were investigated by real-time Fourier transform infrared spectra (RTIR), thermogravimetric analysis/infrared spectrometry (TG-IR), and direct pyrolysis/mass (DP-MS). The morphologies of the formed chars were observed by scanning electron microscopy (SEM) demonstrating the most effective amount of POPHA is 20 wt %.