BackgroundThe improvement of bone ingrowth into prosthesis and enhancement of the combination of the range between the bone and prosthesis are important for long-term stability of artificial joints. They are the focus of research on uncemented artificial joints. Porous materials can be of potential use to solve these problems.Objectives/PurposesThis research aims to observe the characteristics of the new porous Ti-25Nb alloy and its biocompatibility in vitro, and to provide basic experimental evidence for the development of new porous prostheses or bone implants for bone tissue regeneration.MethodsThe Ti-25Nb alloys with different porosities were fabricated using powder metallurgy. The alloys were then evaluated based on several characteristics, such as mechanical properties, purity, pore size, and porosity. To evaluate biocompatibility, the specimens were subjected to methylthiazol tetrazolium (MTT) colorimetric assay, cell adhesion and proliferation assay using acridine staining, scanning electron microscopy, and detection of inflammation factor interleukin-6 (IL-6).ResultsThe porous Ti-25Nb alloy with interconnected pores had a pore size of 200 µm to 500 µm, which was favorable for bone ingrowth. The compressive strength of the alloy was similar to that of cortical bone, while with the elastic modulus closer to cancellous bone. MTT assay showed that the alloy had no adverse reaction to rabbit bone marrow mesenchymal stem cells, with a toxicity level of 0 to 1. Cell adhesion and proliferation experiments showed excellent cell growth on the surface and inside the pores of the alloy. According to the IL-6 levels, the alloy did not cause any obvious inflammatory response.ConclusionAll porous Ti-25Nb alloys showed good biocompatibility regardless of the percentage of porosity. The basic requirement of clinical orthopedic implants was satisfied, which made the alloy a good prospect for biomedical application. The alloy with 70% porosity had the optimum mechanical properties, as well as suitable pore size and porosity, which allowed more bone ingrowth.

The aim of the present study was to observe the performance of Ti-25Nb alloys with various porosities as femoral stem prostheses in a rabbit model, thus providing basic experimental evidence for the development of porous prostheses. The porous Ti-25Nb alloy prostheses were designed according to the morphology of the medullary cavity. These prostheses were placed into the femoral medullary cavities in 36 New Zealand white rabbits. Postoperative X-ray films, scanning electron microscopy (SEM) of the implant interface, energy-dispersive spectroscopy (EDS) analysis of the implant surface, pulling-out test and general observations were conducted. The specimens showed good biocompatibility; there was no obvious bone absorption in porous Ti-25Nb specimens with different porosities at different time points observed using X-ray films. Under SEM examination, calcium deposits were observed inside the pores and in the interface between bone and prostheses. The EDS analysis demonstrated that calcium deposits were present on the surface of the prostheses at the eight-week point postoperatively. The pulling-out test showed good bonding strength between bone and implant; after pulling out, the surface and inside the pores of the prostheses all presented bone mass. Porous Ti-25Nb alloy implants presents good biocompatibility as well as providing a biological fixation between the bone and implant. A porosity of 70% is more advantageous to the newborn bone ingrowth, combined with achieving a more solid bone-implant interface.

The compressive strength and the biocompatibility were assessed for the porous Ti-25 wt%Nb alloy fabricated by the combination of the sponge impregnation technique and sintering technique. The alloy provided pore sizes of 300-600 μm, porosity levels of 71 ± 1.5%, in which the volume fraction of open pores was 94 ± 1.3%. The measurements also showed that the alloy had the compressive Young's modulus of 2.23 ± 0.5 GPa and the strength of 98.4 ± 4.5 MPa, indicating that the mechanical properties of the alloy are similar to those of human bone. The scanning electron microscopy (SEM) observations revealed that the pores were well connected to form three-dimension (3D) network open cell structure. Moreover, no obvious impurities were detected in the porous structure. The experiments also confirmed that rabbit bone mesenchymal stem cells (MSCs) could adhere and proliferate in the porous Ti-25 wt%Nb alloy. The interactions between the porous alloy and the cells are attributed to the porous structure with relatively higher surface. The suitable mechanical and biocompatible properties confirmed that this material has a promising potential in the application for tissue engineering.

Since the L12 structured Al3Ti alloy exists only in a narrow compositional range, further alloying of the single phase Ll2 alloy to improve its property seems hardly successful. Developing two-phase or multiphase Al3Ti alloys may be an effective approach for strengthening and toughening. In this article, a new type of Al3Ti-based alloy which has a Ll2 matrix with precipitates of a second phase is reported. The quaternary alloys based on Al67Mn8Ti25, and modified with Nb additions, consist of an Ll2 matrix and DO22 second phase particles in the annealed state, but the second phase can be dissolved by solution treatment and precipitated during high temperature aging. Remarkable strenghtening and promising compressive ductility were exhibited by the experimental alloy. The influence of composition on the microstructure and properties of the alloys are reported also.