The performance and modification mechanism of Buton rock asphalt (BRA) modified asphalt were analyzed. The road performance of modified asphalt was observed and compared with SBS modified asphalt to confirm the modification mechanism. Four‐component test, and dynamic shear rheological tests were conducted to identify the performance of modified asphalt. Fourier transform infrared spectroscopy was carried out to analyze the modification mechanism of modified asphalt. Finally, the rutting, low‐temperature bending beam failure, and freeze–thaw splitting tests were used to evaluate the high‐temperature performance, low‐temperature cracking resistance, and water stability performance of mixtures, respectively. The results show that the high‐temperature performance of asphalt can be improved by BRA with asphaltene and resin increased. It is likely that there is no new functional group generated and this process was physical changes mainly. The honeycomb structure of BRA ashes/particles increased the contact area between the base asphalt and BRA ashes/particles, which makes the asphalt change from the homogeneous body into a two‐phase continuous structure system. Consequently, the adhesion between asphalt and BRA ashes/particles was enhanced, and the dynamic stability, bending coefficient and splitting strength ratio were improved. It indicates that the test results of asphalt mixtures verified the modification effect of BRA. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019, 136, 46903.

To improve the low-temperature performance of the Buton rock asphalt (BRA)-modified asphalt, styrene-butadiene rubber (SBR) was added to it. The BRA-modified asphalt and SBR-BRA composite modified asphalt were prepared by high-speed shearing method. The penetration, softening point, ductility, and Brookfield viscosity of the two kinds of asphalt were measured. The dynamic shear rheometer (DSR) and the beam bending rheometer (BBR) were employed to research the performance of BRA-modified asphalt by adding SBR. The results showed that the pure asphalt in BRA was the main reason to reduce the low-temperature performance of neat asphalt when the content of BRA was 19%. However, the ash in BRA was the main factor to reduce the low-temperature performance when its content was more than 39.8%. When the BRA content was 59.8%, the SBR-BRA composite modified asphalt with SBR contents of 2%, 4%, 6%, and 8%, and it shows that the penetration and ductility of the BRA-modified asphalt are increased by the addition of SBR. The equivalent brittle point was reduced, the stiffness modulus was decreased, and the creep rate was increased. At the same time, the Brookfield viscosity was reduced and the rutting factor was increased. The stiffness modulus of the SBR-BRA composite modified asphalt mixture was increased. That is to say, when SBR was mixed into the BRA-modified asphalt, the low-temperature performance could be remarkably improved based on ensuring high-temperature performance. The low-temperature index of composite modified asphalt was analyzed. It was recommended to apply the equivalent brittle point to evaluate the low-temperature performance of SBR-BRA composite modified asphalt.

No abstract

In order to explore the moduli decay patterns of asphalt mixtures under different loading conditions, the nonlinear fatigue damage model was implemented in order to simulate the moduli decay patterns. Then, the direct tensile, indirect tensile, and uniaxial compression fatigue tests were employed under four kinds of stress levels with four parallel tests. The specimens of AC-13C Styrene-butadiene-styrene (SBS) modified mixtures were manufactured. Based on the test results, the decay patterns of the moduli during fatigue tests under different stress states were revealed, and the parameters of the damage model under different test conditions were obtained. By changing the values of the model parameters under a certain loading condition, fatigue curves were obtained. Then, the fatigue properties of asphalt mixtures under different stress states could be compared and analyzed directly. The result indicated that the evolution curves of fatigue damage for the direct tensile test, the indirect tensile test, and the uniaxial compression test all experienced three stages, which indicates that the fatigue damage characteristic of asphalt mixtures is non-linear. The decay patterns of the direct tensile moduli and the tensile moduli measured by the indirect tensile test are similar. The decay patterns of the uniaxial compression and the compression moduli measured by indirect tensile test are similar. The decay patterns of tensile and compressive moduli are obviously different. At the same cycle ratio state, the position of the decay curve for the compression moduli is higher than that of the tensile moduli. It indicates that the tensile failure is the main reason of the fatigue damage for asphalt mixture. The new analysis method of fatigue damage was proposed, which provides a possibility to compare the fatigue results that were obtained from different loading conditions and different specimen sizes. traffic and environmental conditions have been conducted [12,13]. In order to ensure the durability and usability of asphalt pavement, many researchers have been conducting the works of evaluation of fatigue characteristics via varied fatigue test methods in different specimen's size and different stress levels.Xie Jun suggested that the direct tension strength got larger at higher strain loading rate [14]. Hyung Suk Lee conducted an indirect tensile test and determined the fundamental viscoelastic material property, which means that the strength of asphalt mixture were related to the temperature and loading time [15]. Waleed A. Zeiada employed the uniaxial compression test and observed that the fatigue endurance limit value increases by the increasing of temperature, asphalt content, and rest periods, whereas it decreased when the volume of air voids increases [16]. Different test methods produce different results. So far, three traditional test methods have been employed extensively: the direct tensile test, the indirect tensile test, and the uniaxial compression test. The direct tensile test refers to the test of a material ...

Modulus testing methods under various test conditions have a large influence on modulus test results, which hinders the accurate evaluation of the stiffness of asphalt mixtures. In order to decrease the uncertainty in the stiffness characteristics of asphalt mixtures under various stress states, the traditional unconfined compression test, direct tensile test, and the synchronous test method, based on the indirect tension and four-point bending tests, were carried out for different loading frequencies. Results showed that modulus test results were highly sensitive to the shape, size, and stress state of the specimen. Additionally, existing modulus characteristics did not reduce these differences. There is a certain correlation between the elastic modulus ratio and the frequency ratio for asphalt under multiple stress states. The modulus, under multiple stress states, was processed using min–max normalization. Then, the standardization model for tensile and compressive characteristics of asphalt under diverse stress states was established based on the sample preparation, modulus ratio variations, and loading frequency ratio. A method for deriving other moduli from one modulus was realized. It is difficult to evaluate the stiffness performance in diverse stress states for asphalt by only using conventional compressive and tensile tests. However, taking into account the effects of stress states and loading frequencies, standardized models can be used to reduce or even eliminate these effects. The model realizes the unification of different modulus test results, and provides a theoretical, methodological, and technical basis for objectively evaluating moduli.