Identification of the active site is important in developing rational design strategies for solid catalysts but is seriously blocked by their structural complexity. Here, we use uniform Cu nanocrystals synthesized by a morphology-preserved reduction of corresponding uniform Cu2O nanocrystals in order to identify the most active Cu facet for low-temperature water gas shift (WGS) reaction. Cu cubes enclosed with {100} facets are very active in catalyzing the WGS reaction up to 548 K while Cu octahedra enclosed with {111} facets are inactive. The Cu–Cu suboxide (CuxO, x ≥ 10) interface of Cu(100) surface is the active site on which all elementary surface reactions within the catalytic cycle proceed smoothly. However, the formate intermediate was found stable at the Cu–CuxO interface of Cu(111) surface with consequent accumulation and poisoning of the surface at low temperatures. Thereafter, Cu cubes-supported ZnO catalysts are successfully developed with extremely high activity in low-temperature WGS reaction.

Cu–ZnO–Al2O3 catalysts are used as the industrial catalysts for water gas shift (WGS) and CO hydrogenation to methanol reactions. Herein, via a comprehensive experimental and theoretical calculation study of a series of ZnO/Cu nanocrystals inverse catalysts with well-defined Cu structures, we report that the ZnO–Cu catalysts undergo Cu structure-dependent and reaction-sensitive in situ restructuring during WGS and CO hydrogenation reactions under typical reaction conditions, forming the active sites of CuCu(100)-hydroxylated ZnO ensemble and CuCu(611)Zn alloy, respectively. These results provide insights into the active sites of Cu–ZnO catalysts for the WGS and CO hydrogenation reactions and reveal the Cu structural effects, and offer the feasible guideline for optimizing the structures of Cu–ZnO–Al2O3 catalysts.

The identification of the contribution of different surface sites to the catalytic activity of a catalyst nanoparticle is one of the most challenging issues in the fundamental studies of heterogeneous catalysis. We herein demonstrate an effective strategy of using a series of uniform cubic Cu2O nanocrystals with different sizes to identify the intrinsic activity and contributions of face and edge sites in the catalysis of CO oxidation by a combination of reaction kinetics analysis and DFT calculations. Cu2O nanocrystals undergo in situ surface oxidation forming CuO thin films during CO oxidation. As the average size of the cubic Cu2O nanocrystals decreases from 1029 nm to 34 nm, the dominant active sites contributing to the catalytic activity switch from face sites to edge sites. These results reveal the interplay between the intrinsic catalytic activity and the density of individual types of surface sites on a catalyst nanoparticle in determining their contributions to the catalytic activity.

P-type Cu2 O has been long considered as an attractive photocatalyst for photocatalytic water reduction, but few successful examples has been reported. Here, we report the synthesis of TiO2 (core)/Cu2 O (ultrathin film shell) nanorods by a redox reaction between Cu(2+) and in-situ generated Ti(3+) when Cu(2+) -exchanged H-titanate nanotubes are calcined in air. Owing to the strong TiO2 -Cu2 O interfacial interaction, TiO2 (core)/Cu2 O (ultrathin film shell) nanorods are highly active and stable in photocatalytic water reduction. The TiO2 core and Cu2 O ultrathin film shell respectively act as the photosensitizer and cocatalyst, and both the photoexcited electrons in the conduction band and the holes in the valence band of TiO2 respectively transfer to the conduction band and valence band of the Cu2 O ultrathin film shell. Our results unambiguously show that Cu2 O itself can act as the highly active and stable cocatalyst for photocatalytic water reduction.

H2O2 is widely used as an oxidant for photocatalytic methane conversion to value-added chemicals over oxide-based photocatalysts under mild conditions, but suffers from low utilization efficiencies. Herein, we report that O2 is an efficient molecular additive to enhance the utilization efficiency of H2O2 by suppressing H2O2 adsorption on oxides and consequent photogenerated holes-mediated H2O2 dissociation into O2. In photocatalytic methane conversion over an anatase TiO2 nanocrystals predominantly enclosed by the {001} facets (denoted as TiO2{001})-C3N4 composite photocatalyst at room temperature and ambient pressure, O2 additive significantly enhances the utilization efficiency of H2O2 up to 93.3%, giving formic acid and liquid-phase oxygenates selectivities respectively of 69.8% and 97% and a formic acid yield of 486 μmolHCOOH·gcatalyst−1·h−1. Efficient charge separation within TiO2{001}-C3N4 heterojunctions, photogenerated holes-mediated activation of CH4 into ·CH3 radicals on TiO2{001} and photogenerated electrons-mediated activation of H2O2 into ·OOH radicals on C3N4, and preferential dissociative adsorption of methanol on TiO2{001} are responsible for the active and selective photocatalytic conversion of methane to formic acid over TiO2{001}-C3N4 composite photocatalyst.