The development of flexible electronic skins with high sensitivities and multimodal sensing capabilities is of great interest for applications ranging from human healthcare monitoring to robotic skins to prosthetic limbs. Although piezoresistive composite elastomers have shown great promise in this area of research, typically poor sensitivities and low response times, as well as signal drifts with temperature, have prevented further development of these materials in electronic skin applications. Here, we introduce and demonstrate a design of flexible electronic skins based on composite elastomer films that contain interlocked microdome arrays and display giant tunneling piezoresistance. Our design substantially increases the change in contact area upon loading and enables an extreme resistance-switching behavior (ROFF/RON of ∼10(5)). This translates into high sensitivity to pressure (-15.1 kPa(-1), ∼0.2 Pa minimum detection) and rapid response/relaxation times (∼0.04 s), with a minimal dependence on temperature variation. We show that our sensors can sensitively monitor human breathing flows and voice vibrations, highlighting their potential use in wearable human-health monitoring systems.

Stretchable electronic skins with multidirectional force-sensing capabilities are of great importance in robotics, prosthetics, and rehabilitation devices. Inspired by the interlocked microstructures found in epidermal-dermal ridges in human skin, piezoresistive interlocked microdome arrays are employed for stress-direction-sensitive, stretchable electronic skins. Here we show that these arrays possess highly sensitive detection capability of various mechanical stimuli including normal, shear, stretching, bending, and twisting forces. Furthermore, the unique geometry of interlocked microdome arrays enables the differentiation of various mechanical stimuli because the arrays exhibit different levels of deformation depending on the direction of applied forces, thus providing different sensory output patterns. In addition, we show that the electronic skins attached on human skin in the arm and wrist areas are able to distinguish various mechanical stimuli applied in different directions and can selectively monitor different intensities and directions of air flows and vibrations.

Shape- and dopant-controlled magnetic semiconductor nanocrystals have been achieved by the thermolysis of nonpyrophoric and less reactive single molecular precursors under a monosurfactant system. Reaction parameters governing both the intrinsic crystalline phase and the growth regime (kinetic vs thermodynamic) are found to be important for the synthesis of various shapes of MnS nanocrystals that include cubes, spheres, 1-dimensional (1-D) monowires, and branched wires (bipods, tripods, and tetrapods). Obtained nanowires exhibit enhanced optical and magnetic properties compared to those of 0-D nanospheres. Proper choice of molecular precursors and kinetically driven low-temperature growth afford dopant controlled 1-D Cd1-xMn(x)S nanorods at high levels (up to approximately 12%) of Mn, which is supported by repeated surface exchange experiments and X-ray diffraction (XRD) and electron paramagnetic resonance (EPR) analyses.

Polylactic acid (PLA) is a promising biomass-derived polymer, but is currently synthesized by a two-step process: fermentative production of lactic acid followed by chemical polymerization. Here we report production of PLA homopolymer and its copolymer, poly(3-hydroxybutyrate-co-lactate), P(3HB-co-LA), by direct fermentation of metabolically engineered Escherichia coli. As shown in an accompanying paper, introduction of the heterologous metabolic pathways involving engineered propionate CoA-transferase and polyhydroxyalkanoate (PHA) synthase for the efficient generation of lactyl-CoA and incorporation of lactyl-CoA into the polymer, respectively, allowed synthesis of PLA and P(3HB-co-LA) in E. coli, but at relatively low efficiency. In this study, the metabolic pathways of E. coli were further engineered by knocking out the ackA, ppc, and adhE genes and by replacing the promoters of the ldhA and acs genes with the trc promoter based on in silico genome-scale metabolic flux analysis in addition to rational approach. Using this engineered strain, PLA homopolymer could be produced up to 11 wt% from glucose. Also, P(3HB-co-LA) copolymers containing 55-86 mol% lactate could be produced up to 56 wt% from glucose and 3HB. P(3HB-co-LA) copolymers containing up to 70 mol% lactate could be produced to 46 wt% from glucose alone by introducing the Cupriavidus necator beta-ketothiolase and acetoacetyl-CoA reductase genes. Thus, the strategy of combined metabolic engineering and enzyme engineering allowed efficient bio-based one-step production of PLA and its copolymers. This strategy should be generally useful for developing other engineered organisms capable of producing various unnatural polymers by direct fermentation from renewable resources.

For patients who suffer from sensorineural hearing loss by damaged or loss of hair cells in the cochlea, biomimetic artificial cochleas to remedy the dis­advantages of existing implant systems have been intensively studied. Here, a new concept of an inorganic‐based piezoelectric acoustic nanosensor (iPANS) for the purpose of a biomimetic artificial hair cell to mimic the functions of the original human hair cells is introduced. A trapezoidal silicone‐based membrane (SM) mimics the function of the natural basilar membrane for frequency selectivity, and a flexible iPANS is fabricated on the SM utilizing a laser lift‐off technology to overcome the brittle characteristics of inorganic piezoelectric materials. The vibration amplitude vs piezoelectric sensing signals are theoretically examined based on the experimental conditions by finite element analysis. The SM is successful at separating the audible frequency range of incoming sound, vibrating distinctively according to varying locations of different sound frequencies, thus allowing iPANS to convert tiny vibration displacement of ≈15 nm into an electrical sensing output of ≈55 μV, which is close to the simulation results presented. This conceptual iPANS of flexible inorganic piezoelectric materials sheds light on the new fields of nature‐inspired biomimetic systems using inherently high piezoelectric charge constants.