decades, heuristic approaches have been successfully used to enhance the performance of OSCs, including synthesis of new donor and acceptor molecules, [5][6][7][8][9][10] optimization of the interface and morphology, [11][12][13][14][15] ternary blending, [16][17][18][19] and device engineering. [20][21][22][23] As a result, power conversion efficiency (PCE) of OSCs has surpassed 15% for single-layer bulkheterojunction systems. [24,25] As the PCE of OSCs is getting closer to the requirements for commercial applications and competing technology, the most efficient OSCs also need to perform consistently or maintain low efficiency loss throughout their lifetimes. [26][27][28] To make organic photovoltaics commercially viable and competitive, researchers have been making efforts on characterizing, understanding, and rationally engineering the long-term stability of OSC devices. [26,[29][30][31][32][33][34][35][36][37][38] Generally, the performance degradation of OSCs comes from the oxidation of electrodes, degradation of the interface layers, and changes in the morphology of the active layer. Among these factors, the oxidation of electrodes and the degradation of the interface layers are attributed to exposure to oxygen and moisture, [39,40] and these drawbacks can be largely prevented by encapsulation. [41,42] However, the intrinsic instability of active layer morphology driven by light, temperature, and thermodynamics cannot be prevented by encapsulation. In-depth studies were carried out to understand the stability of the active layers under multiple stresses. [43] For instance, McGehee and co-workers [29] reported that solar cells based on amorphous materials would suffer from open-circuit voltage (V OC ) burnin degradation resulted from the impact of light-induced traps, and this degradation can be reduced by using materials with high degree of crystallinity. Brabec group [33] demonstrated that the light-induced [6,6]-phenyl-C 61 -butyric acid methyl ester (PCBM) dimerization would lead to the short-circuit current density (J SC ) loss after aging, while this dimerization can be inhibited by a high degree of polymer-fullerene mixing and it can also be reduced via increasing the crystallization of the fullerene domains. Brabec and co-workers [34] found that burnin degradation driven by low miscibility is the major short-time Long device lifetime is still a missing key requirement in the commercialization of nonfullerene acceptor (NFA) organic solar cell technology. Understanding thermodynamic factors driving morphology degradation or stabilization is correspondingly lacking. In this report, thermodynamics is combined with morphology to elucidate the instability of highly efficient PTB7-Th:IEICO-4F binary solar cells and to rationally use PC 71 BM in ternary solar cells to reduce the loss in the power conversion efficiency from ≈35% to <10% after storage for 90 days and at the same time improve performance. The hypomiscibility observed for IEICO-4F in PTB7-Th (below the percolation threshold) leads to overpurific...

Alternative low-temperature solution-processed hole-transporting materials (HTMs) without dopant are critical for highly efficient perovskite solar cells (PSCs). Here, two novel small molecule HTMs with linear π-conjugated structure, 4,4'-bis(4-(di-p-toyl)aminostyryl)biphenyl (TPASBP) and 1,4'-bis(4-(di-p-toyl)aminostyryl)benzene (TPASB), are applied as hole-transporting layer (HTL) by low-temperature (sub-100 °C) solution-processed method in p-i-n PSCs. Compared with standard poly(3,4-ethylenedioxythiophene): poly(styrenesulfonic acid) (PEDOT:PSS) HTL, both TPASBP and TPASB HTLs can promote the growth of perovskite (CH NH PbI ) film consisting of large grains and less grain boundaries. Furthermore, the hole extraction at HTL/CH NH PbI interface and the hole transport in HTL are also more efficient under the conditions of using TPASBP or TPASB as HTL. Hence, the photovoltaic performance of the PSCs is dramatically enhanced, leading to the high efficiencies of 17.4% and 17.6% for the PSCs using TPASBP and TPASB as HTL, respectively, which are ≈40% higher than that of the standard PSC using PEDOT:PSS HTL.

The impact of two kinds of additives, such as 1,8-octanedithiol (ODT), 1,8-diiodooctane (DIO), diphenylether (DPE), and 1-chloronaphthalene (CN), on the performance of poly[(5,6-difluoro-2,1,3-benzothiadiazol-4,7-diyl)-alt-(3,3‴-di(2-octyldodecyl)2,2';5',2″;5″,2‴-quaterthiophen-5,5‴-diyl)] (PffBT4T-2OD):[6,6]-phenyl-C71-butyric acid methyl ester (PC71BM) based polymer solar cell are investigated. The polymer solar cells (PSCs) of PffBT4T-2OD:PC71BM by using CN show a more improved PCE of 10.23%. The solubility difference of PffBT4T-2OD in DIO and CN creates the fine transformation in phase separation and favorable nanoscale morphology. Grazing incidence X-ray diffraction (GIXRD) data clearly shows molecular stacking and orientation of the active layer. Interestingly, DIO and CN have different functions on the effect of the molecular orientation. These interesting studies provide important guidance to optimize and control complicated molecular orientations and nanoscale morphology of PffBT4T-2OD based thick films for the application in PSCs.

A novel asymmetrical squaraine ASQ-5 bearing indoline as an end capper exhibits a low bandgap of 1.43 eV and a broad absorption band in the Vis-NIR region of 550-850 nm in thin films, hence renders solution-processed organic solar cells with an impressive Jsc of up to 11.03 mA cm(-2) and an excellent PCE of 4.29%.