Conductive polymer hydrogels are receiving considerable attention in applications such as soft robots and human-machine interfaces. Herein, a transparent and highly ionically conductive hydrogel that integrates sensing, UV-filtering, water-retaining, and anti-freezing performances is achieved by the organic combination of tannic acid-coated hydroxyapatite nanowires (TA@HAP NWs), polyvinyl alcohol (PVA) chains, ethylene glycol (EG), and metal ions. The highly ionic conductivity of the hydrogel enables tensile strain, pressure, and temperature sensing capabilities. In particular, in terms of the hydrogel strain sensors based on ionic conduction, it has high sensitivity (GF = 2.84) within a wide strain range (350%), high linearity (R 2 = 0.99003), fast response (≈50 ms) and excellent cycle stability. In addition, the incorporated TA@HAP NWs act as a nano-reinforced filler to improve the mechanical properties and confer a UV-shielding ability upon the hydrogel due to its size effect and the characteristics of absorbing ultraviolet light waves, which can reflect and absorb short ultraviolet rays and transmit visible light. Meanwhile, owing to the water-locking effect between EG and water molecules, the hydrogel exhibits freezing resistance at low temperatures and moisture retention at high temperatures. This biocompatible and multifunctional conductive hydrogel provides new ideas for the design of novel ionic skin devices.

Over zeolite H-ZSM-5, the aromatics-based hydrocarbon-pool mechanism of methanol-to-olefins (MTO) reaction was studied by GC-MS, solid-state NMR spectroscopy, and theoretical calculations. Isotopic-labeling experimental results demonstrated that polymethylbenzenes (MBs) are intimately correlated with the formation of olefin products in the initial stage. More importantly, three types of cyclopentenyl cations (1,3-dimethylcyclopentenyl, 1,2,3-trimethylcyclopentenyl, and 1,3,4-trimethylcyclopentenyl cations) and a pentamethylbenzenium ion were for the first time identified by solid-state NMR spectroscopy and DFT calculations under both co-feeding ([(13) C6 ]benzene and methanol) conditions and typical MTO working (feeding [(13) C]methanol alone) conditions. The comparable reactivity of the MBs (from xylene to tetramethylbenzene) and the carbocations (trimethylcyclopentenyl and pentamethylbenzium ions) in the MTO reaction was revealed by (13) C-labeling experiments, evidencing that they work together through a paring mechanism to produce propene. The paring route in a full aromatics-based catalytic cycle was also supported by theoretical DFT calculations.

Previously, an inverted phase (the minority blocks comprising the continuum phase) was found in solution-cast block copolymer thin films. In this study, the effect of casting solvents on the formation of inverted phase has been studied. Two block copolymers, poly(styrene-b-butadiene) (SB) (M w = 73 930 Da) and poly(styrene-b-butadiene-b-styrene) (SBS) (M w = 140 000 Da), with comparable block lengths and equal polystyrene (PS) weight fraction (∼30 wt %) were used. The copolymer thin films were cast from different solvents, toluene, benzene, cyclohexane, and binary mixtures of benzene and cyclohexane. Toluene and benzene are good solvents for both PS and PB, but have a preferential affinity for PS, while cyclohexane is a good solvent for PB but a ϑ solvent for PS (T ϑ = 34.5 °C). The differential solvent affinity for PS and PB was estimated in terms of a difference between the polymer−solvent interaction parameter, χ, for each block. Under an extremely slow solvent evaporation rate, the time-dependent phase behavior during such a solution-to-film process was examined by freeze-drying the samples at different stages, corresponding to different copolymer concentrations, φ. Our results indicate that the slight interaction difference between solvent and each block influences the effective volume fraction of each domain and drives the solution to form a transient inverted phase at the early stage of the microphase separation.