2 Molecular design of non-fullerene acceptors (NFAs) is of vital importance for highefficiency organic solar cells. The branched alkyl chain modification is often regarded as a counter-intuitive approach as which may introduce undesirable steric hindrance that reduces charge transport in NFAs. Here we show the design and synthesis of a highly efficient NFA family by substituting the beta position of thiophene unit on Y6-based A-DAD-A backbone with branched alkyl chains. It was found that such modification of different alkyl chain length could completely change the molecular packing behavior of NFAs, leading to improved structure order and charge transport in thin films. Unprecedented efficiency of 18.32% (certified value of 17.9%) with a fill factor of 81.5% is achieved for single-junction organic solar cells. This work reveals the importance of branched alkyl chain topology in tuning the molecular packing and blend morphology that leads to improved organic photovoltaic performance.

Enhancing the luminescence property without sacrificing the charge collection is one key to high-performance organic solar cells (OSCs), while limited by the severe non-radiative charge recombination. Here, we demonstrate efficient OSCs with high luminescence via the design and synthesis of an asymmetric non-fullerene acceptor, BO-5Cl. Blending BO-5Cl with the PM6 donor leads to a record-high electroluminescence external quantum efficiency of 0.1%, which results in a low non-radiative voltage loss of 0.178 eV and a power conversion efficiency (PCE) over 15%. Importantly, incorporating BO-5Cl as the third component into a widely-studied donor:acceptor (D:A) blend, PM6:BO-4Cl, allows device displaying a high certified PCE of 18.2%. Our joint experimental and theoretical studies unveil that more diverse D:A interfacial conformations formed by asymmetric acceptor induce optimized blend interfacial energetics, which contributes to the improved device performance via balancing charge generation and recombination.

Highly efficient electron extraction is achieved by using a photoconductive cathode interlayer in inverted ternary organic solar cells (OSCs) where a near-IR absorbing porphyrin molecule is used as the sensitizer. The OSCs show improved device performance when the ratio of the two donors varies in a large region and a maximum power conversion efficiency up to 11.03% is demonstrated.

The differences between the introduction of chlorine and fluorine atoms to small-molecule acceptors were deeply investigated. From the single-crystal structures of three molecules, the Cl-substitution intervention into the molecular configuration and packing mainly lies in three aspects as follows: single molecule configuration, one direction of the intermolecular arrangement, and three-dimensional (3D) molecular packing. First, the introduction of the chlorine atom in IDIC-4Cl leads to a more planar molecular configuration than IDIC-4H and IDIC-4F because of the formation of a molecular interlocked network induced by the strong Cl•••S intermolecular interactions. Second, IDIC-4Cl shows the closest π−π stacking distance and the smallest dihedral angle (0°) between adjacent molecules to form ideal J-aggregation, which should be beneficial for charge transportation between different connected molecules in this direction. Finally, the interlocked interactions between Cl and S atoms lead to a highly ordered 3D molecular packing, in which the end groups will form an ideal overlapped packing among different molecules, whereas the other two analogues with H or F show less ordered packing of their 1,1dicyanomethylene-3-indanone ending groups. Organic solar cells based on IDIC-4Cl show the highest power conversion efficiency (PCE) of 9.24%, whereas the PCEs of IDIC-4H-and IDIC-4F-based devices are 4.57 and 7.10%, respectively.

The concentration-dependent absorption and temperature-dependent fluorescence of the perylene bisimide dye PBI 1 in methylcyclohexane point to a biphasic aggregation behavior. At intermediate concentrations and temperatures, respectively, a dimer with low fluorescence yield dominates, which cannot be extended to longer aggregates. Those are formed at high concentrations and low temperatures, respectively, via a second, energetically unfavorable dimer species that acts as a nucleus. A corresponding aggregation model reproduces accurately the concentration dependence and allows extracting the equilibrium constants and spectra of the distinct species. The differences in the photophysical properties indicate H-type excitonic coupling for the favored dimer and J-type characteristics for the extended aggregates which could be related to structural models based on DFT calculations. The energetics can be understood by considering hydrogen-bonding and π-π-stacking interactions.