In this study, antibacterial activity of extruded ginseng extract by 60 and 80% Et-OH were investigated by agar diffusion assay against two bacteria causing dental caries (Streptococcus mutans and Lactobacillus casei). Extrusion conditions were 20% moisture content 100 o C and 140 o C barrel temperature. The inhibition effect of 60% Et-OH ginseng extract was higher than 80% Et-OH ginseng extract. The minimum inhibitory concentration (MIC) of 80% Et-OH extruded ginseng extract at 140 and 100 o C barrel temperature against L.casei were 100 and 150 mg/mL respectively using broth assay method. The amount of glucosyltransferase (GTase)

Damaged the Jeoguibon (patterns of the Queen's ceremonial robe) was found during repair work of Daejojeon, Changdeok Palace in 2011. Analytical study on seven colors painted in the patterns has been conducted by P-XRF and Micro-XRD analysis. The result displays that red lead, ultramarine blue, conichalcite or mixed pigment of emerald green and barium white, orpiment and white lead had been used on the patterns. Comparison of the pigments used for the Pyeseulbon (patterns of the Queen's belt ornament covering knees in the front) housed in National Museum of Korea has revealed that not only red lead but also cinnabar and organic pigment had been used in the Jeoguibon and the Pyeseulbon housed in National Museum of Korea. In addition the same pigments has been examined in green and yellow parts of both the Jeoguibon in Daejojeon and the Pyeseulbon housed in National Museum of Korea. The result has shown that western's synthetic green pigment such as emerald green was introduced and used in 1920's. The scientific result from this study expects to be used as useful referencing data for the comparative understanding on pigments used in palace during the 20th century.

: This paper was researched that provenance of the raw material for bronze relics excavated Cheonghaejin using the distribution of lead isotope ratio based on galena ores of South Korea. Also we want to make sure that the trace elements appearing as a by-product can be used as a secondary indicator for provenance research. In the case of the galena map of the East-North Asia (Mabuchi, 1985), data are plotted in China area. Therefore it is estimated that most bronzes were produced with lead ore from China. On the other hand, the same data are plotted in the Okcheon Metamorphic Belt and Yeongnam Massif of the galena map of South Korea (KOPLID, 2012). Also the contents of Ag and Sb are available as indicator due to separate ores from similar zone in lead isotope ratio.

Purpose:The objective of this study was to compare the surface roughness according to polishing process in conventional laboratory techniques used for polishing three different acrylic denture base resins.Materials and methods: Specimen preparation and surface polishing procedures were conducted to manufacturer's recommendation with three heat-polymerized denture base resins. Surface roughness and gloss were measured by a contact type tester and a LED gloss checker using thickness 2 mm and diameter 10 mm. There were five specimens for each acrylic resin material and polishing procedures.Mean average surface roughness (Ra) values of each specimen group were analyzed using a one-way ANOVA analysis of variance and Scheffe's post hoc test. Surfaces after surface roughness and gloss testing according to each polishing process were evaluated under a stereoscopic microscope.Results: The highest mean average surface roughness was measured(Ra=2.43 0.47) for surfaces finished with a denture tungsten carbide bur in Triplex. The lowest surface roughness values (Ra=0.11 0.07) were determined in Vertex polished with a lathe. In addition, all materials revealed that surface roughness determined highly in HP1 and HP2 than other procedures.All correlation between surface roughness and gloss showed highly with three heat-polymerized resins. Specially, topmost correlation revealed than other material in Triplex. Significant differences in mean average surface roughness were found between polishing process used high speed lathe and low speed hand-piece.Conclusion: Laboratory polishing used to high speed was found to produce the smoothest surface of heatpolymerized denture base acrylic resin. Therefore, we recommended that high polishing process need to get smooth surface.[Abstract] 205

This study revealed the material composition and characteristics of 19 glass fragments excavated from stone chamber No. 1 of Jeongchon Tomb in Naju through chemical composition analyses and observations. These characteristics were compared with the characteristics of the glass fragments excavated from No. 3 tomb of Bogam-ri in Naju. The purpose of this study was to identify the characteristics of the ancient glass of the Mahan-Baekje period. The glass fragments excavated from the Jeongchon Tombs can be classified into purplish blue, light-purplish blue, greenish blue, green, and mixture of purple blue and purple, based on their color. These beads were made using a drawn and casting technique. In addition, blue glass fragments were primarily excavated form No. 3 tomb of Bogam-ri. However, red glass fragments were not excavated from either of the tombs. According to chemical composition analyses, soda glass group and potash glass group were common in both the tombs. Additionally, alkali mixed glass group and lead barium glass group were excavated from Jeongchon Tombs and No. 3 tomb of Bogam-ri, respectively. The glass fragments excavated from No. 3 tomb of Bogam-ri have more color variations than those excavated from Jeongchon Tombs.