Comparison of Flowrate and Occlusion in a Vertical Infusion Pump and Horizontal Infusion Pump

Ahniar, Nur Hasanah; Marwazi, Hendra; Yufita, Rismarini

doi:10.35882/jeeemi.v2i1.1

Cited by 3 publications

(2 citation statements)

References 5 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Flowrate and grafting are important parts for the infusion pump to run properly or be fit for use. As has been done by Nur Hasanah Ahniar et al, comparing the types of vertical and horizontal infusion pumps [18].…”

Section: Introductionmentioning

confidence: 99%

Development of Infusion Device Analyzer Equipped with Occlusion Detection and a Real-Time Parameters Monitoring on Computer System

Maghfiroh

Havilda

Das³

2022

j.teknokes

View full text Add to dashboard Cite

Medical infusion device provides drugs or fluids directly through a blood vessel. However, the occurrence of occlusion in the infusion device causes the incoming drug fluid does not to flow constantly, and pressure is formed on the infusion tube. When an infusion device has been used for a long time, there will be a change in the precision of the flow and pressure values. Furthermore, a calibration process must be carried out at least once a year. This research aims to design an infusion device analyzer which able to show parameters in a graphic equipped with occlusion parameters and Bluetooth communication in real-time to the computer unit. This study uses a solenoid valve for pressure simulation. The allowable occlusion limit is <20 Psi. The SKU 237545 sensor detects the water pressure that is blocked by the solenoid valve. Then the data will be displayed on the Parallax data acquisitions using Bluetooth communication. The Parallax data acquisitions will display real-time occlusion data, data averages, instant values, and graphs. The results of the IDA design, when tested using the Syringe Pump TOP 5300, obtained an average of 0.68 Psi. Meanwhile, when the IDA design was tested using the Infusion Pump 3300, it brought 0.73 Psi. Furthermore, it showed that the occlusion parameter was compared with the Fluke IDA 4, a mean error was 0.7 Psi. Therefore, it can be concluded that this IDA design can be used for calibration to see the feasibility of an infusion pump or syringe pump.

show abstract

Section: Introductionmentioning

confidence: 99%

Development of Infusion Device Analyzer Equipped with Occlusion Detection and a Real-Time Parameters Monitoring on Computer System

Maghfiroh

Havilda

Das³

2022

j.teknokes

View full text Add to dashboard Cite

show abstract

“…[18] in 2020 the study of Comparison of Flowrate and Occlusion in a Vertical Infusion Pump and Horizontal Infusion Pump presented Infusion pump droplets can be controlled and monitored using infrared sensors. [19] A study by Syaifuddin et all used an STM32 microcontroller with photodiode and infrared sensor installed in the chamber to read flow rate. [20] The device integrates a 16x2 character LCD display.…”

Section: Introductionmentioning

confidence: 99%

Accuracy of Infrared Photodiode Sensors at The Flowrate Measurement in Infusion Device Analyzer with 2 Channel TFT Display

Azizah,

Rahmawati,

Syaifudin

2023

Indones.J.electronic.electromed.med.inf

View full text Add to dashboard Cite

The use of infusion is crucial for patient healing. Infusion refers to a fluid that consists of drugs, nutrients, and hydration delivered continuously into the patient's bloodstream over a specific period. One of the types of infusion devices is the infusion pump and syringe pump. These devices play a vital role in accurately and precisely controlling the volume or flow rate of fluids. However, continuous usage of these devices can sometimes result in inaccurate measurements, which can affect their overall accuracy. The accuracy of these devices is crucial for proper dosage administration to patients, particularly in critical situations. Therefore, it is necessary to periodically calibrate healthcare devices, at least once a year, as specified in Ministry of Health Regulation No. 54 of 2015. Calibration is an activity performed to determine the true value of a device. The objective of this study is to develop an Infusion Device Analyzer (IDA) with a TFT LCD display that showcases graphical representations of flow rate parameters. By analyzing the calculation of flow rate values using Infrared Photodiode sensors, the stability of the flow rate graph can be observed on a 7-inch TFT LCD display. The measurement involved the use of two different brands of syringe pumps and two different brands of infusion pumps. The results were presented in real-time on the 7-inch TFT LCD display, both in graphical and numerical formats. Additionally, the data was transmitted via Bluetooth to a PC, allowing the graph to be simultaneously displayed in a Delphi program.The measurement results revealed performance errors when using the Terumo Syringe Pump with Terumo syringes in Channel 1, with values of 0.45% (10 ml/h), 0.72% (50 ml/h), and 0.40% (100 ml/h). In Channel 2, the errors were 0.32% (10 ml/h), 0.40% (50 ml/h), and 0.32% (100 ml/h). When using the B-Braun Syringe Pump with B-Braun syringes, Channel 1 exhibited errors of 0.45% (10 ml/h), 0.7% (50 ml/h), and 0.85% (100 ml/h), while Channel 2 had errors of 0.8% (10 ml/h), 0.3% (50 ml/h), and 1% (100 ml/h). In the case of the Terumo Infusion Pump with Terumo Infusion Sets, Channel 1 showed errors of 0.4% (10 ml/h), 0.5% (50 ml/h), and 0.45% (100 ml/h), and Channel 2 exhibited errors of 0.32% (10 ml/h), 0.4% (50 ml/h), and 0.72% (100 ml/h). Lastly, when using the B-Braun Infusion Pump with B-Braun Infusion Sets, Channel 1 had errors of 0.72% (10 ml/h), 1% (50 ml/h), and 1,2% (100 ml/h), while Channel 2 displayed errors of 0.8% (10 ml/h), 0.72% (50 ml/h), and 0,4% (100 ml/h).INDEX TERMS Infrared Photodiode Sensor, Calibration, Real Time, Flow Rate.

show abstract

Microcontroller based infusion device analyzer with flowrate parameter

Wijaya

Rahmasari²,

Amelia

2022

The 2nd International Conference of Science and Information Technology in Smart Administration (Icsintesa 2021)

View full text Add to dashboard Cite

Comparison of Flowrate and Occlusion in a Vertical Infusion Pump and Horizontal Infusion Pump

Cited by 3 publications

References 5 publications

Development of Infusion Device Analyzer Equipped with Occlusion Detection and a Real-Time Parameters Monitoring on Computer System

Development of Infusion Device Analyzer Equipped with Occlusion Detection and a Real-Time Parameters Monitoring on Computer System

Accuracy of Infrared Photodiode Sensors at The Flowrate Measurement in Infusion Device Analyzer with 2 Channel TFT Display

Microcontroller based infusion device analyzer with flowrate parameter

Contact Info

Product

Resources

About