Electroplated Nanocomposites of High Wear Resistance for Advanced Systems Application

Timoshkov, I. V.; Kurmashev, V. I.; Timoshkov, Vadim

doi:10.5772/17510

Cited by 6 publications

(6 citation statements)

References 16 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Some manufacturing processes such as LIGA (Lithography, Electroplating, and Molding) [24], laser micromachining [25], microextrusion additive manufacturing [26], micro-EDM (Electrical Discharge Machining) [27] , and mechanical micromachining [28] have been used to generate small precision component and micro-structured parts [29].…”

Section: Introductionmentioning

confidence: 99%

A Review on Nanocomposites. Part 1: Mechanical Properties

Liu

Khaliq

Huo

et al. 2020

Journal of Manufacturing Science and Engineering

View full text Add to dashboard Cite

Micromachining of nanocomposites is deemed to be a complicated process due to the anisotropic, heterogeneous structure, and advanced mechanical properties of these materials associated with the size effects in micromachining. It leads to poorer machinability in terms of high cutting force, low surface quality, and high rate of tool wear. In part 1 of this two-part review paper, a comprehensive review on mechanical properties of various nanocomposites will be presented while the second part of the paper will focus on the micro-machinability of these nanocomposite materials.

show abstract

Section: Introductionmentioning

confidence: 99%

A Review on Nanocomposites. Part 1: Mechanical Properties

Liu

Khaliq

Huo

et al. 2020

Journal of Manufacturing Science and Engineering

View full text Add to dashboard Cite

show abstract

“…The effect of temperature can be taken as insignificant that is supported by the result of the study of Schlesinger and Paunovic due to the factor of 2.98 [9]. On the other hand, some of the studies claim that iincrease in the temperature led to decrease in the internal stress [4,5,10]. Table 1 showing the number of increments (U).…”

Section: Resultsmentioning

confidence: 60%

“…The stress that is in the range of 30 MPa in electrodeposits up to 100 µm thickness can be considered as acceptable [3]. It was concluded that increasing the temperature decreased the internal stress [4,5]. The combination of parameters that produce minimum internal stress during Ni-MoS 2 electro-co-deposition was investigated in this study.…”

Section: Introductionmentioning

confidence: 99%

Taguchi Design of Internal Stress and Friction Measurements during Electrodeposition

Güler¹,

Karakaya²

2017

J Material Sci Eng

View full text Add to dashboard Cite

The electroplating method is a promising alternative to produce composite plating by using dispersed fine particles in the metal plating bath. The process can be either called electro-deposition or composite deposition. The particles are trapped in the deposit during the process. Internal stress is a common problem in plated deposits that affect the performance of the coatings and may even result in adhesion problems. Hence, the amount and type (compressive or tensile) of the internal stress must be controlled. MoS 2 particle -nickel coatings can be referred as self-lubricating coatings that satisfy the demand for decreased friction in severe applications. The internal stress during MoS 2 particle -nickel electro-deposition was measured by deposit stress analyzer. The effects of electroplating parameters that are MoS 2 particle concentration, temperature and coating thickness on the internal stress values were investigated by Taguchi design. It is found that increasing MoS 2 particle concentration and coating thickness led to decrease in the internal stress developed during MoS 2 -nickel composite coatings. Interaction effects of these parameters were also revealed.

show abstract

“…As indicated in Figure 1, the model of nanoparticles co-deposition suggested by Timoshkov et al [35], is based on the following stages:…”

Section: Models Including the Hydrodynamics Of Fluidsmentioning

confidence: 99%

Electrochemical Synthesis of Nanocomposites

Abdel-Karim¹

2016

Electrodeposition of Composite Materials

View full text Add to dashboard Cite

Tνis cνapter presents an overview of researcν efforts focused on botν fabrication and properties of nanocomposites prepared by electrodeposition. Tνe nanoparticles can improve tνe base material in terms of wear resistance, dampinμ properties, and mecνanical strenμtν as well as electrical properties. Different kinds of matrix, sucν as metals, polymers, and ceramic matrix, νave been employed for tνe production of composites reinforced by nano-ceramic particles sucν as carbides, nitrides, and oxides as well as carbon nanotubes. Tνeoretical aspects and mecνanisms related to tνe electrodeposition process of nanocomposite films, from aqueous solutions, are discussed.

show abstract

Electroplated Nanocomposites of High Wear Resistance for Advanced Systems Application

Cited by 6 publications

References 16 publications

A Review on Nanocomposites. Part 1: Mechanical Properties

A Review on Nanocomposites. Part 1: Mechanical Properties

Taguchi Design of Internal Stress and Friction Measurements during Electrodeposition

Electrochemical Synthesis of Nanocomposites

Contact Info

Product

Resources

About