Kinetic experiments were performed to induce of the green methyl dye adsorption from aqueous solution on the bauxite clay. This study includes  determination of  the adsorption capacity of  bauxite clay to methyl green dye adsorption and study the effect of some parameters  ( temperature , time ) on the kinetic of the adsorption process of the dye were studied. Quantity of dye adsorbed was increased when the temperature increases from 298 to 318K which indicates that methyl green adsorption processes are endothermic nature . In order to describe the kinetic data and the rate adsorption constants of the pseudo-first-order and  second-order kinetics were used . The kinetics data were applied well with the second-order kinetic model. From  activation energy value (Ea)   for methyl green dye are energetically favorable and the dye adsorption  includes  physical  and chemical adsorption types

Refractive indices (nD), viscosities (η) and densities (ρ) were deliberated for the binary mixtures created by dipropyl amine with 1-octanol, 1-heptanol, 1-hexanol, 1-pentanol and tert-pentyl alcohol at temperature 298.15 K over the perfect installation extent. The function of Redlich-Kister were used to calculate and renovated of the refractive index deviations (∆nD), viscosity deviations (ηE), excess molar Gibbs free energy (∆G*E) and excess molar volumes (VmE) The standard errors and coefficients were respected by this function. The values of ∆nD, ηE, VmE and ∆G*E were plotted against mole fraction of dipropyl amine. In all cases the obtained ηE, ∆G*E, VmE and ∆nD values were negative at 298.15K. Effect of carbon atoms number in the chain of alcohol and hydroxyl groups' position on molecular interactions in these mixtures has also been discussed.

Multi-walled carbon nanotubes from cheap tubs company MWCNT-CP were purified by alcohol \ H2O2 \ separation funnel which is simple, easy and scalable techniques. The steps of purification were characterized by X-ray diffraction, Raman spectroscopy, scanning electron microscopy SEM with energy dispersive of X-ray spectroscopy EDX and surface area measurements. The technique was succeeded to remove most the trace element from MWCNT-CP which causing increase the surface area. The ratios of impurities were reduced to less 0.6% after treatment by three steps with losing less than 5% from MWCNT-CP.

A polypyrrole-based ammonia-detection gas sensor was studied in this work. Under a 1.6 V electrodeposition potential, polypyrrole (PPy) was electrochemically synthesized from an aqueous solution of 0.1 M pyrrole and 0.1 M oxalic acid. An extension to the polypyrrole films was applied through electrochemical deposition on indium tin oxide (ITO), using the metal oxide nanoparticles of MgO and WO3. These films were investigated for their sensing behavior towards NH3 at different working temperatures and different weight percentages of nanoparticles .The measurements of A.C conductivity were conducted over a frequency range of 101-105 Hz and temperature range of 298-423 K . The highest electrical conductivity was equal to 3.67x10-1 Ω.cm-1 at a temperature of 323 K and frequency of 105H z. The experimental results showed that the sensitivity of the undoped and doped PPy with nanoparticle films to ammonia gas changes with the change in temperature and weight percentage.

To understand the nature of molecular aggregation between two solvents, excess properties (e.g. excess molar volume (V ), excess Gibb's free energy of activation viscous flow (∆G* E ) and viscosity deviation of binary mixtures) are therefore needed. Thus, in the current study, the refractive index (nD), viscosity (η), and density (ρ) of binary mixtures were measured for tetrahydrofurfuryl alcohol (THFA) with ethanol, 2-propanol and 2-butanol at 298.15K. Moreover and based on experimentally obtained results, the V , the refractive index deviation (∆nD), excess molar viscosity (η E ) and ∆G* E were calculated. To correct and fit the experimental V , η