This study investigated the optical properties and flexural strength of translucent TZP layered with high-translucent PSZ using resin cement of various shades. Zirconia specimens (translucent TZP; Zpex and high-translucent PSZ; ZpexSmile) were 13 mm in diameter, layered at thickness ratios of 0.3/0.7, 0.5/0.5, and 0.7/0.3 mm (ZpexSmile/Zpex), and then luted using resin cement of 3 shades. Monolithic specimens of both were used as controls. CIE L*a*b* color coordinates and translucency parameter (TP) were evaluated as optical properties. Biaxial flexural strength was also determined as a mechanical evaluation. The a* and b* values of layered specimens varied depending on the shade of cement. TP values were not affected by shade of cement and thickness ratio. The biaxial flexural strength was intermediate value between both monolithic specimens. The layering method of zirconia with various translucencies using resin cement of different shades can improve color expression while maintaining clinically sufficient flexural strength.

Yttrium tetragonal zirconia polycrystal frameworks were prepared for all-ceramic fixed partial dentures (FPDs) for the mandibular incisor region. The effects of the cross-sectional area and morphology of the connector on its strength were evaluated by fracture tests. Nine types of zirconia framework for a 3-unit FPD for a defect of 1 mandibular central incisor were prepared, each differing in cross-sectional area and morphology. Fracture tests were performed by loading until fracture using a universal testing machine. Fracture load was determined and fracture site examined. Significant differences were observed in fracture load according to the morphology and crosssectional area of the connector (p<0.05, p<0.01, p<0.001). Fracture load differed significantly among all groups according to cross-sectional area, and was also greater when the shape of the connector formed an isosceles triangle widest at the base and the connector had the same height and width. These values still far exceeded 311 N, however, which is the average occlusal force in the incisor region. The results of this study suggest that connector design affects fracture load.

Many types of interdental instrument, such as dental floss and interdental brushes, can be purchased easily and sell in large numbers. Many studies have compared the effects of such instruments. Few studies have investigated their relationship with regions of residual plaque, however. The purpose of this study was to compare rates of plaque removal from the mesial and distal surfaces of the bilateral maxillary and mandibular premolars and molars among 3 types of interdental instrument: finger-winding-dental floss, holder-type dental floss, and an interdental brush. Prior to the experiment, the artificial teeth in a jaw model were removed for application of artificial plaque. The teeth were then replaced and the model attached to a phantom. An operator brushed the teeth in a posture close to that adopted in actual tooth brushing with each type of instrument, after which the plaque removal rate was compared among them. The rate of plaque removal using finger-winding floss was the highest, although this type of instrument is less easy to hold than the others. The rate with a handle-equipped interdental instrument showed a decrease in some regions, although it is easy to hold. The results of this study suggest that the type of interdental instrument used should differ depending on the region to be cleaned.

The purpose of the present study was to investigate the relationship between mastication and head posture using foods with different degrees of hardness. A total of 12 healthy, dentulous volunteers participated in the study. Each participant was required to chew two types of gummy candy with two levels of hardness while sitting upright. Measurements were conducted using an optoelectric jaw-tracking system with 6 degrees of freedom (Gnatho-Hexagraph II JM-2000 ® ). The horizontal plane perpendicular to the direction of gravitational force served as the reference plane. Analysis of the gradient of the Frankfurt plane (head posture) and pitching of the head during masticatory movement was conducted. The influence of the type of test food on these parameters was evaluated during mastication. During stable mastication, the gradient of the Frankfurt plane was 4.66 degrees on average, close to the horizontal plane. The time course of the Frankfurt plane gradient revealed a tendency toward dorsal flexion during the first to middle phases of mastication, and a tendency toward ventral flexion during the middle to last phases, regardless of the hardness of the test food. The participants were divided into two groups based on change in head posture during chewing. The results showed while there was no change in head posture in the group with marked pitching of the head, head posture did change in the group with little pitching.

The goal of the present study was to clarify the status of training in clinical dentistry at training facilities belonging to Tokyo Dental College by investigating trainee quota fill rates and analyzing the relationship between selection of training program and subsequent career pathway. The trainees were divided into 4 groups based on career pathway after training: those entering graduate school; those becoming residents; those remaining at the college or hospital to take specialized clinical courses or for other purposes; and those starting work outside the college. The trainee quota fill rate was highest at the Suidobashi Hospital, followed by the Ichikawa General and Chiba Hospitals. A total of 8 training programs have been implemented at these facilities (Chiba: A, B, C, and D; Suidobashi, A, B, and C; and Ichikawa, A). A comparison among training programs revealed that the fill rate exceeded 60% in all cases, except for Chiba D, where it was markedly lower, at 25%. Career pathway after training significantly varied between training facilities. Among trainees selecting the Chiba Hospital, the highest proportion was occupied by those starting work outside the college. The proportion of those entering graduate school was also high in this group. Similarly, among trainees selecting the Suidobashi Hospital, the highest proportion was occupied by those starting work outside the college. The proportion of those entering graduate school was low in this group, however. Among trainees selecting the Ichikawa General Hospital, the proportions of those entering graduate school and those becoming residents were particularly high, while the proportion of those starting work outside the college was low. A comparison of career pathways revealed a significant difference only between Chiba Programs B and C. In conclusion, training facility showed a markedly stronger influence on career pathway than training program.