We demonstrate single molecule conductance as a sensitive and atomically precise probe of binding configurations of adenine and its biologically relevant variants on gold. By combining experimental measurements and density functional theory (DFT) calculations of single molecule–metal junction structures in aqueous conditions, we determine for the first time that robust binding of adenine occurs in neutral or basic pH when the molecule is deprotonated at the imidazole moiety. The molecule binds through the donation of the electron lone pairs from the imidazole nitrogen atoms, N7 and N9, to the gold electrodes. In addition, the pyrimidine ring nitrogen, N3, can bind concurrently and strengthen the overall metal–molecule interaction. The amine does not participate in binding to gold in contrast to most other amine-terminated molecular wires due to the planar geometry of the nucleobase. DFT calculations reveal the importance of interface charge transfer in stabilizing the experimentally observed binding configurations. We demonstrate that biologically relevant variants of adenine, 6-methyladenine and 2′-deoxyadenosine, have distinct conductance signatures. These results lay the foundation for biosensing on gold using single molecule conductance readout.

Chemical bonding in native oxides of GaAs, before and after etching, is detected by X-Ray Photoelectron Spectroscopy (XPS). It is correlated with surface energy engineering (SEE), measured via Three Liquid Contact Angle Analysis (3LCAA), and oxygen coverage, measured by High Resolution Ion Beam Analysis (HR-IBA).Before etching, GaAs native oxides are found to be hydrophobic with an average surface energy, γT, of 33 ± 1 mJ/m2, as measured by 3LCAA. After dilute NH4OH etching, GaAs becomes highly hydrophilic and its surface energy, γT, increases by a factor 2 to a reproducible value of 66 ± 1 mJ/m2. Using HR-IBA, oxygen coverage on GaAs is found to decrease from 7.2 ± 0.5 monolayers (ML) to 3.6 ± 0.5 ML. The 1.17 ratio of Ga to As, measured by HR-IBA, remains constant after etching.XPS is used to measure oxidation of Ga and As, as well as surface stoichiometry on two locations of several GaAs(100) wafers before and after etching. The relative proportions of Ga and As are unaffected by adventitious carbon contamination. The 1.16 Ga:As ratio, measured by XPS, matches HR-IBA analysis. The proportions of oxidized Ga and As do not change significantly after etching. However, the initial ratio of As2O5 to As2O3, within the oxidized As, significantly decreases after etching from approximately 3:1 to 3:2.Absolute oxygen coverage, as a function of surface processing, is determined within 0.5 ML by HR-IBA. XPS offers insight into these modifications by detecting electronic states and phase composition changes of GaAs oxides. The changes in surface chemistry are correlated to changes in hydro-affinity and surface energies measured by 3LCAA.

No abstract

Liquid phase analysis dominates the field of blood diagnostics and requires drawing blood volumes of several ml for each test. To achieve acceptable accuracy, each single liquid blood test requires ∼7 mL per blood sample, and repeated blood tests are often needed. Frequent testing ca result in Hospital Acquired Anemia for infants, chronically ill, and critically ill patients. Blood testing methods that can be utilized with small amounts of blood are a critical need to save lives. Theranos claimed to have developed novel methods requiring only a few nL of blood. However, Theranos’ techniques led to errors that exceeded beyond the medically acceptable threshold of 10%. This work investigates solid state blood analysis using low volumes of several µL. The most common blood tests used as first line for diagnostics and monitoring patients’ status, always include blood electrolytes, iron, and in some cases, heavy metals.The present work investigates the formation of rapidly solidified Homogeneous Thin Solid Films (HTSFs) formed from blood drops, in order to make them suitable for solid state analysis in vacuo and in air. The solidification of ∼5 micro-liter (µL)-sized blood droplets into HTSFs is studied with two goals: achieve reproducible HTSFs optimized for producing accurate analysis, and successfully measure the potential accuracy of measurements made on HTSFs for blood electrolytes Na, K, Mg, Ca, and Cl and heavy metals such as Fe.The blood volumes selected for this work are in the µL range, one thousandth volumes drawn for current liquid phase analysis. Balanced Saline Solution (BSS) is used as an initial liquid for testing solidification uniformity and a potential calibration material. Next, canine and human blood are studied on two types of HemaDropTM coatings for solidification: super-hydrophilic and hyper-hydrophilic. HTSF formation from BSS and blood drops are compared on both coated and uncoated surfaces.Three solid state analytical methods are investigated in parallel to probe composition at different depths and test each for reproducibility and accuracy: Ion Beam Analysis (IBA), X-ray Fluorescence (XRF), and X-ray Photoelectron Spectroscopy (XPS). The results show that using solid films of blood yields composition, which can be reproducibly measured by IBA, XPS and XRF to varying degrees. XPS’s depth of analysis, limited to ∼5 nm, probes a small fraction of the HTSF, but provides insights into the range of thickness for homogeneous compositions in HTSFs. Statistical and error analysis help establish whether measurements taken in sets of three typically used in lab fall below the medically accepted error threshold (<10%) for each technique and element detected. Measurements are repeated and taken at various locations and on different HTSFs to establish reproducibility. XRF is of particular interest, because it is fast, accurate, portable and can be conducted in air, making it ideal for areas with limited resources.

No abstract