The effects of crystal orientation and doping on the surface energy, γT, of native oxides of Si(100) and Si(111) are measured via Three Liquid Contact Angle Analysis (3LCAA) to extract γT, while Ion Beam Analysis (IBA) is used to detect Oxygen. During 3LCAA, contact angles for three liquids are measured with photographs via the “Drop and Reflection Operative Program (DROP™). DROP™ removes subjectivity in image analysis, and yields reproducible contact angles within < ±1°. Unlike to the Sessile Drop Method, DROP can yield relative errors < 3% on sets of 20-30 drops. Native oxides on 5 x 1013 B/cm3 p- doped Si(100) wafers, as received in sealed, 25 wafer teflon boats continuously stored in Class 100/ISO 5 conditions at 24.5°C in 25% controlled humidity, are found to be hydrophilic. Their γT, 52.5 ± 1.5 mJ/m2, is reproducible between four boats from three sources, and 9% greater than γT of native oxides on n- doped Si(111), which averages 48.1 ± 1.6 mJ/m2 on four 4” Si(111) wafers. IBA combining 16O nuclear resonance with channeling detects 30% more oxygen on native oxides of Si(111) than Si(100). While γT should increase on thinner, more defective oxides, Lifshitz-Van der Waals interactions γLW on native oxides of Si(100) remain at 36 ± 0.4 mJ/m2, equal to γLW on Si(111), 36 ± 0.6 mJ/m2, since γLW arises from the same SiO2 molecules. Native oxides on 4.5 x 1018 B/cm3 p+ doped Si(100) yield a γT of 39 ± 1 mJ/m2, as they are thicker per IBA. In summary, 3LCAA and IBA can detect reproducibly and accurately, within a few %, changes in the surface energy of native oxides due to thickness and surface composition arising from doping or crystal structure, if conducted in well controlled clean room conditions for measurements and storage.

Chemical bonding in native oxides of GaAs, before and after etching, is detected by X-Ray Photoelectron Spectroscopy (XPS). It is correlated with surface energy engineering (SEE), measured via Three Liquid Contact Angle Analysis (3LCAA), and oxygen coverage, measured by High Resolution Ion Beam Analysis (HR-IBA).Before etching, GaAs native oxides are found to be hydrophobic with an average surface energy, γT, of 33 ± 1 mJ/m2, as measured by 3LCAA. After dilute NH4OH etching, GaAs becomes highly hydrophilic and its surface energy, γT, increases by a factor 2 to a reproducible value of 66 ± 1 mJ/m2. Using HR-IBA, oxygen coverage on GaAs is found to decrease from 7.2 ± 0.5 monolayers (ML) to 3.6 ± 0.5 ML. The 1.17 ratio of Ga to As, measured by HR-IBA, remains constant after etching.XPS is used to measure oxidation of Ga and As, as well as surface stoichiometry on two locations of several GaAs(100) wafers before and after etching. The relative proportions of Ga and As are unaffected by adventitious carbon contamination. The 1.16 Ga:As ratio, measured by XPS, matches HR-IBA analysis. The proportions of oxidized Ga and As do not change significantly after etching. However, the initial ratio of As2O5 to As2O3, within the oxidized As, significantly decreases after etching from approximately 3:1 to 3:2.Absolute oxygen coverage, as a function of surface processing, is determined within 0.5 ML by HR-IBA. XPS offers insight into these modifications by detecting electronic states and phase composition changes of GaAs oxides. The changes in surface chemistry are correlated to changes in hydro-affinity and surface energies measured by 3LCAA.

No abstract

Analysis of the total surface energy γTand its three components as established by the van Oss-Chaudhury-Good Theory (vOCG) is conducted via Three Liquid Contact Angle Analysis (3LCAA). γTis correlated with the composition of the top monolayers (ML) obtained from High-Resolution Ion Beam Analysis (HR-IBA). Control of γTenables surface engineering for wafer bonding (Nano-BondingTM) and/or epitaxial growth. Native oxides on boron-doped p-Si(100) are found to average γTof 53 ± 1.4 mJ/m2) and are always hydrophilic. An HF in methanol or aqueous HF etch for 60 s always renders Si(100) hydrophobic. Its γTdecreases by 20% to 44 ± 3 mJ/m2in HF in methanol etch and by 10% to 48 ± 3 mJ/m2in aqueous HF. On the contrary, GaAs(100) native oxides are found to always be hydrophobic. Tellurium n+-doped GaAs(100) yields an average of γTof 37 ± 2 mJ/m2, 96% of which is due to the Lifshitz-Van der Waals molecular interactions (γLW= 36 ± 1 mJ/m2). However, hydrophobic GaAs(100) can be made highly hydrophilic. After etching, γTincreases by almost 50% to 66 ± 1.4 mJ/m2. 3LCAA shows that the γTincrease is due to electron acceptor and donor interactions, while the Lifshitz-van der Waals energy γLWremains constant. IBA combining the 3.039 ± 0.01 MeV oxygen nuclear resonance with <111> channeling, shows that oxygen on Si(100) decreases by 10% after aqueous HF etching, from 13.3 ± 0.3 monolayers (ML) to 11.8 ± 0.4 ML 1 hour after etch.Te-doped GaAs(100) exhibits consistent oxygen coverage of 7.2 ± 1.4 ML, decreasing by 50% after etching to a highly hydrophilic surface with 3.6 ± 0.2 oxygen ML. IBA shows that etching does not modify the GaAs surface stoichiometry to within 1% . Combining 3LCAA with HR-IBA provides a quantitative metrology to measure how GaAs and Si surfaces can be altered to a different hydroaffinity and surface termination.