We report reversible adhesion switching on porous fibrillar polystyrene-block-poly(2-vinyl pyridine) (PS-b-P2VP) adhesive pads by humidity changes. Adhesion at a relative humidity of 90% was more than nine times higher than at a relative humidity of 2%. On nonporous fibrillar adhesive pads of the same material, adhesion increased only by a factor of ~3.3. The switching performance remained unchanged in at least 10 successive high/low humidity cycles. Main origin of enhanced adhesion at high humidity is the humidity-induced decrease in the elastic modulus of the polar component P2VP rather than capillary force. The presence of spongelike continuous internal pore systems with walls consisting of P2VP significantly leveraged this effect. Fibrillar adhesive pads on which adhesion is switchable by humidity changes may be used for preconcentration of airborne particulates, pollutants, and germs combined with triggered surface cleaning.

Many insect species reversibly adhere to surfaces by combining contact splitting (contact formation via fibrillar contact elements) and wet adhesion (supply of liquid secretion via pores in the insects’ feet). Here, we fabricate insect-inspired fibrillar pads for wet adhesion containing continuous pore systems through which liquid is supplied to the contact interfaces. Synergistic interaction of capillarity and humidity-induced pad softening increases the pull-off force and the work of adhesion by two orders of magnitude. This increase and the independence of pull-off force on the applied load are caused by the capillarity-supported formation of solid–solid contact between pad and the surface. Solid–solid contact dominates adhesion at high humidity and capillarity at low humidity. At low humidity, the work of adhesion strongly depends on the amount of liquid deposited on the surface and, therefore, on contact duration. These results may pave the way for the design of insect-inspired adhesive pads.

Bioinspired surface topographies showing generic anti-adhesive behaviour by minimization of the real contact area not only with rigid, but also with soft and compliant counterpart surfaces recently attracted increasing attention. In the present study, we show that such generic anti-adhesive surfaces, which moreover demonstrate anti-fouling behaviour, can be produced on a large scale by a simple double replication of monolayers of microspheres with diameters of a few 10 μm. Thus, we obtained mechanically stable monolithic arrays of microspheres tightly connected to a support of the same material. Adhesion of these microsphere arrays to sticky and compliant counterpart surfaces was one order of magnitude weaker than that of flat control samples of the same material. The generation of nanorod arrays with nanorod diameters of a few 100 nm as the second hierarchical structure level on monolithic microsphere arrays did not significantly affect the adhesion force. The experimental data on anti-adhesive behaviour were modelled using a modified Johnson-Kendall-Roberts theoretical approach that also provided general design criteria for topographic adhesion minimization to sticky counterpart surfaces.

We designed spongy monoliths allowing liquid delivery to their surfaces through continuous nanopore systems (mean pore diameter ∼40 nm). These nanoporous monoliths were flat or patterned with microspherical structures a few tens of microns in diameter, and their surfaces consisted of aprotic polymer or of TiO2 coatings. Liquid may reduce adhesion forces FAd; possible reasons include screening of solid-solid interactions and poroelastic effects. Softening-induced deformation of flat polymeric monoliths upon contact formation in the presence of liquids enhanced the work of separation WSe. On flat TiO2-coated monoliths, WSe was smaller under wet conditions than under dry conditions, possibly because of liquid-induced screening of solid-solid interactions. Under dry conditions, WSe is larger on flat TiO2-coated monoliths than on flat monoliths with a polymeric surface. However, under wet conditions, liquid-induced softening results in larger WSe on flat monoliths with a polymeric surface than on flat monoliths with an oxidic surface. Monolithic microsphere arrays show antiadhesive properties; FAd and WSe are reduced by at least 1 order of magnitude as compared to flat nanoporous counterparts. On nanoporous monolithic microsphere arrays, capillarity (WSe is larger under wet than under dry conditions) and solid-solid interactions (WSe is larger on oxide than on polymer) dominate contact mechanics. Thus, the microsphere topography reduces the impact of softening-induced surface deformation and screening of solid-solid interactions associated with liquid supply. Overall, simple modifications of surface topography and chemistry combined with delivery of liquid to the contact interface allow adjusting WSe and FAd over at least 1 order of magnitude. Adhesion management with spongy monoliths exploiting deployment (or drainage) of interfacial liquids as well as induction or prevention of liquid-induced softening of the monoliths may pave the way for the design of artificial surfaces with tailored contact mechanics. Moreover, the results reported here may contribute to better understanding of the contact mechanics of biological surfaces.

Silicon, a ubiquitous material in modern computing, is an emerging platform for realizing a source of indistinguishable single photons on demand. The integration of recently discovered single-photon emitters in silicon into photonic structures is advantageous to exploit their full potential for integrated photonic quantum technologies. Here, we show the integration of an ensemble of telecom photon emitters in a two-dimensional array of silicon nanopillars. We developed a top-down nanofabrication method, enabling the production of thousands of nanopillars per square millimeter with state-of-the-art photonic-circuit pitch, all the while being free of fabrication-related radiation damage defects. We found a waveguiding effect of the 1278 nm-G center emission along individual pillars accompanied by improved brightness compared to that of bulk silicon. These results unlock clear pathways to monolithically integrating single-photon emitters into a photonic platform at a scale that matches the required pitch of quantum photonic circuits.