No abstract

An overview is given of the applications of short and ultrashort lasers in material processing. Shorter pulses reduce heat-affected damage of the material and opens new ways for nanometer accuracy. Even forty years after the development of the laser there is a lot of effort in developing new and better performing lasers. The driving force is higher accuracy at reasonable cost, which is realised by compact systems delivering short laser pulses of high beam quality. Another trend is the shift towards shorter wavelengths, which are better absorbed by the material and which allows smaller feature sizes to be produced. Examples of new products, which became possible by this technique, are given. The trends in miniaturization as predicted by Moore and Taniguchi are expected to continue over the next decade too thanks to short and ultrashort laser machining techniques. After the age of steam and the age of electricity we have entered the age of photons now Keywords: Micro-machining, Laser, Ablation 101, (Figure 2.3) has simulated the interaction and ablation behaviour of aluminium, copper and silicon at 266 nm wavelength. The optical penetration depth was 7, 12 and 5 nm respectively. The applied power density was in the range of 5 to 50.109 W/cm2. It was found that the material evaporates as small particles (0.3-10 nm), most of them smaller than 1 nm. The average velocity of

SummaryThe relevance of topographic cues for commitment of induced pluripotent stem cells (iPSCs) is largely unknown. In this study, we demonstrate that groove-ridge structures with a periodicity in the submicrometer range induce elongation of iPSC colonies, guide the orientation of apical actin fibers, and direct the polarity of cell division. Elongation of iPSC colonies impacts also on their intrinsic molecular patterning, which seems to be orchestrated from the rim of the colonies. BMP4-induced differentiation is enhanced in elongated colonies, and the submicron grooves impact on the spatial modulation of YAP activity upon induction with this morphogen. Interestingly, TAZ, a YAP paralog, shows distinct cytoskeletal localization in iPSCs. These findings demonstrate that topography can guide orientation and organization of iPSC colonies, which may affect the interaction between mechanosensors and mechanotransducers in iPSCs.

Two-photon polymerization (TPP) offers the possibility of creating artificial cell scaffolds composed of micro- and nanostructures with spatial resolutions of less than 1 µm. For use in tissue engineering, the identification of a TPP-processable polymer that provides biocompatibility, biofunctionality and appropriate mechanical properties is a difficult task. ECM proteins such as collagen or fibronectin, which could mimic native tissues best, often lack the mechanical stability. Hence, by generating polymer-protein hybrid structures, the beneficial properties of proteins can be combined with the advantageous characteristics of polymers, such as sufficient mechanical stability. This study describes three steps toward facilitated application of TPP for biomaterial generation. (1) The efficiency of a low-cost ps-laser source is compared to a fs-laser source by testing several materials. A novel photoinitiator for polymerization with a ps-laser source is synthesized and proved to enable increased fabrication throughput. (2) The fabrication of 3D-microstructures with both systems and the fabrication of polymer-protein hybrid structures are demonstrated. (3) The tissue engineering capabilities of TPP are demonstrated by creating cross-linked gelatin microstructures, which clearly forced porcine chondrocytes to adapt their cell morphology.

We have analysed and optimised a laser process for the sintering of the TiO2 layers in dye solar cells (DSCs). Through a thermographic characterisation of the process, we show that it is possible to scale and process large areas uniformly (16 cm2). We fabricated DSCs with nanocrystalline (nc)‐TiO2 films sintered by using pulsed ultraviolet laser with an average output power P varying from 1 W to 7 W whilst mainting a constant power conversion efficiency η. The highest efficiency reached for a laser sintered DSC was 7%. The time required to sinter 1 m2 of nc‐TiO2 film was found to decrease hyperbolically with P, which is important for determining process takt times. We quantified the embodied energy (EE) required to sinter 1 m2 of the active TiO2 layer for a variety of different processes, and found that the EE for the laser sintering process with a system wall plug efficiency of 3.5% to be competitive with the more conventional oven and belt furnace treatments. We outline the main features required from a laser system to carry out an efficient, energetically favourable and industrially applicable automated process with competitive throughput. Copyright © 2012 John Wiley & Sons, Ltd.