In this paper, the transonic flow pattern and its influence on heat transfer on a high-pressure turbine blade tip are investigated using experimental and computational methods. Spatially resolved heat transfer data are obtained at conditions representative of a single-stage high-pressure turbine blade (Mexit=1.0, Reexit=1.27×106, gap=1.5% chord) using the transient infrared thermography technique within the Oxford high speed linear cascade research facility. Computational fluid dynamics (CFD) predictions are conducted using the Rolls-Royce HYDRA/PADRAM suite. The CFD solver is able to capture most of the spatial heat flux variations and gives prediction results, which compare well with the experimental data. The results show that the majority of the blade tip experiences a supersonic flow with peak Mach number reaching 1.8. Unlike other low-speed data in the open literature, the turbine blade tip heat transfer is greatly influenced by the shock wave structure inside the tip gap. Oblique shock waves are initiated near the pressure-side edge of the tip, prior to being reflected multiple times between the casing and the tip. Supersonic flow within the tip gap is generally terminated by a normal shock near the exit of the gap. Both measured and calculated heat transfer spatial distributions illustrate very clear stripes as the signature of the multiple shock structure. Overall, the supersonic part of tip experiences noticeably lower heat transfer than that near the leading-edge where the flow inside the tip gap remains subsonic.

This paper presents an experimental and numerical investigation of the aero-thermal performance of an uncooled winglet tip, under transonic conditions. Spatially-resolved heat transfer data, including winglet tip surface and near tip side walls, are obtained using the transient infrared thermography technique within the Oxford High Speed Linear Cascade test facility. CFD predictions are also conducted using the Rolls-Royce HYDRA suite. Most of the spatial heat transfer variations on the tip surface are well-captured by the CFD solver. The transonic flow pattern and its influence on heat transfer are analyzed, which shows that the turbine blade tip heat transfer is greatly influenced by the shock wave structure inside the tip gap. The effect of the casing relative motion is also numerically investigated. The CFD results indicate that the local heat transfer distribution on the tip is affected by the relative casing motion, but the tip flow choking and shock wave structure within the tip gap still exist in the aft region of the blade.

This paper presents an experimental and numerical investigation of the aerothermal performance of an uncooled winglet tip, under transonic conditions. Spatially resolved heat transfer data, including winglet tip surface and near-tip side-walls, are obtained using the transient infrared thermography technique within the Oxford high speed linear cascade test facility. Computational fluid dynamics (CFD) predictions are also conducted using the Rolls-Royce HYDRA suite. Most of the spatial heat transfer variations on the tip surface are well-captured by the CFD solver. The transonic flow pattern and its influence on heat transfer are analyzed, which shows that the turbine blade tip heat transfer is greatly influenced by the shock wave structure inside the tip gap. The effect of the casing relative motion is also numerically investigated. The CFD results indicate that the local heat transfer distribution on the tip is affected by the relative casing motion but the tip flow choking and shock wave structure within the tip gap still exist in the aft region of the blade.

This paper presents an experimental investigation of the aerothermal performance of a cooled winglet tip under transonic conditions (exit Mach number of 1.0, and an exit Reynolds number of 1.27 × 106, based on axial chord). Spatially resolved heat transfer data and film cooling effectiveness data are obtained using the transient infrared thermography technique in the Oxford High-Speed Linear Cascade test facility. Aerodynamic loss data are obtained by traversing a specially made and calibrated three-hole pressure probe and a single-hole probe one axial chord downstream of the blade. Detailed contours of Nusselt number show that for an increase in tip clearance, with and without film cooling, and for coolant injection, for both tip clearances, the Nusselt number increases. Also the smaller tip clearance observes higher film cooling effectiveness overall. Detailed distributions of kinetic energy losses as well as pitch-wise averaged loss coefficients and loss coefficients at a mixed-out plane indicate that the size of the loss core associated with the over-tip leakage vortex decreases with cooling injection.

Progress in the computing power available for CFD predictions now means that full geometry, 3 dimensional predictions are now routinely used in internal cooling system design. This paper reports recent work at Rolls-Royce which has compared the flow and htc predictions in a modern HP turbine cooling system to experiments. The triple pass cooling system includes film cooling vents and inclined ribs. The high resolution heat transfer experiments show that different cooling performance features are predicted with different levels of fidelity by the CFD. The research also revealed the sensitivity of the prediction to accurate modelling of the film cooling hole discharge coefficients and a detailed comparison of the authors’ computer predictions to data available in the literature is reported. Mixed bulk temperature is frequently used in the determination of heat transfer coefficient from experimental data. The current CFD data is used to compare the mixed bulk temperature to the duct centreline temperature. The latter is measured experimentally and the effect of the difference between mixed bulk and centreline temperature is considered in detail.