No abstract

The main component of plasma medicine is the use of low-temperature plasma (LTP) as a powerful tool for biomedical applications. LTP generates high reactivity at low temperatures and can be activated with noble gases with molecular mixtures or compressed air. LTP reactive species are quickly produced, and are a remarkably good source of reactive oxygen and nitrogen species including singlet oxygen (O 2), ozone (O 3), hydroxyl radicals (OH), nitrous oxide (NO), and nitrogen dioxide (NO 2). Its low gas temperature and highly reactive nonequilibrium chemistry make it appropriate for the alteration of inorganic surfaces and delicate biological systems. Treatment of oral biofilm-related infections, treatment of wounds and skin diseases, assistance in cancer treatment, treatment of viruses' infections (e.g. herpes simplex), and optimization of implants surfaces are included among the extensive plasma medicine applications. Each of these applications will be discussed in this review article.

Background: Fluconazole (FLZ) is a drug commonly used for the treatment of Candida infections. However, β-glucans in the extracellular matrices (ECMs) hinder FLZ penetration into Candida biofilms, while extracellular DNA (eDNA) contributes to the biofilm architecture and resistance. Methods: This study characterized biofilms of FLZ-sensitive (S) and -resistant (R) Candida albicans and Candida glabrata in the presence or absence of FLZ focusing on the ECM traits. Biofilms of C. albicans American Type Culture Collection (ATCC) 90028 (CaS), C. albicans ATCC 96901 (CaR), C. glabrata ATCC 2001 (CgS), and C. glabrata ATCC 200918 (CgR) were grown in RPMI medium with or without FLZ at 5× the minimum inhibitory concentration (37°C/48 h). Biofilms were assessed by colony-forming unit (CFU)/mL, biomass, and ECM components (alkali-soluble polysaccharides [ASP], water-soluble polysaccharides [WSP], eDNA, and proteins). Scanning electron microscopy (SEM) was also performed. Data were analyzed by parametric and nonparametric tests (α  =  0.05). Results: In biofilms, FLZ reduced the CFU/mL of all strains (p < 0.001), except for CaS (p = 0.937). However, the ASP quantity in CaS was significantly reduced by FLZ (p = 0.034), while the drug had no effect on the ASP levels in other strains (p > 0.05). Total biomasses and WSP were significantly reduced by FLZ in the ECM of all yeasts (p < 0.001), but levels of eDNA and proteins were unaffected (p > 0.05). FLZ affected the cell morphology and biofilm structure by hindering hyphae formation in CaS and CaR biofilms, by decreasing the number of cells in CgS and CgR biofilms, and by yielding sparsely spaced cell agglomerates on the substrate. Conclusion: FLZ impacts biofilms of C. albicans and C. glabrata as evident by reduced biomass. This reduced biomass coincided with lowered cell numbers and quantity of WSPs. Hyphal production by C. albicans was also reduced.

To investigate surface characteristics (roughness and contact angle), anti-biofilm formation, and mechanical properties (mini-flexural strength) of computeraided design and computer-aided manufacturing (CAD-CAM) polymethylmethacrylate (PMMA) polymer, and three-dimensional (3D) printed resin for denture base fabrication compared with conventional heat polymerized denture base resins. Materials and methods: A total of 60 discs and 40 rectangular specimens were fabricated from one CAD-CAM (AvaDent), one 3D printed (Cosmos Denture), and two conventional heat polymerized (Lucitone 199 and VipiWave) materials for denture base fabrication. Roughness was determined by Ra value; the contact angle was measured by the sessile drop method. The biofilm formation inhibition behavior was analyzed through Candida albicans adhesion, while mini-flexural strength test was done using a three-point bending test. The data were analyzed using descriptive and analytical statistics (α = 0.05). Results:The CAD-CAM PMMA group showed the lowest C. albicans adhesion (log CFU/mL: 3.74 ± 0.57) and highest mini-flexural strength mean (114.96 ± 16.23 MPa). 3D printed specimens presented the highest surface roughness (Ra: 0.317 ± 0.151 μm) and lowest mini-flexural strength values (57.23 ± 9.07 MPa). However, there was no statistical difference between CAD-CAM PMMA and conventional groups for roughness, contact angle, and mini-flexural strength. Conclusions: CAD-CAM milled materials present surface and mechanical properties similar to conventional resins and show improved behavior in preventing C. albicans adhesion. Nevertheless, 3D printed resins present decreased mini-flexural strength.

Background: Infections caused by Candida spp. have been associated with formation of a biofilm, i.e. a complex microstructure of cells adhering to a surface and embedded within an extracellular matrix (ECM). Methods: The ECMs of a wild-type (WT, SN425) and two Candida albicans mutant strains, Δ/Δ tec1 (CJN2330) and Δ/Δ efg1 (CJN2302), were evaluated. Colony-forming units (cfu), total biomass (mg), water-soluble polysaccharides (WSPs), alkali-soluble polysaccharides (ASPs), proteins (insoluble part of biofilms and matrix proteins), and extracellular DNA (eDNA) were quantified. Variable-pressure scanning electron microscopy and confocal scanning laser microscopy were performed. The biovolume (μm 3 /μm