The development of cost‐effective and environmentally acceptable geophysical methods for the exploration of mineral resources is a challenging task. Seismic methods have the potential to delineate the mineral deposits at greater depths with sufficiently high resolution. In hardrock environments, which typically host the majority of metallic mineral deposits, seismic depth‐imaging workflows are challenged by steeply dipping structures, strong heterogeneity and the related wavefield scattering in the overburden as well as the often limited signal‐to‐noise ratio of the acquired data. In this study, we have developed a workflow for imaging a major iron‐oxide deposit at its accurate position in depth domain while simultaneously characterizing the near‐surface glacial overburden including surrounding structures like crossing faults at high resolution. Our workflow has successfully been showcased on a 2D surface seismic legacy data set from the Ludvika mining area in central Sweden acquired in 2016. We applied focusing prestack depth‐imaging techniques to obtain a clear and well‐resolved image of the mineralization down to over 1000 m depth. In order to account for the shallow low‐velocity layer within the depth‐imaging algorithm, we carefully derived a migration velocity model through an integrative approach. This comprised the incorporation of the tomographic near‐surface model, the extension of the velocities down to the main reflectors based on borehole information and conventional semblance analysis. In the final step, the evaluation and update of the velocities by investigation of common image gathers for the main target reflectors were used. Although for our data set the reflections from the mineralization show a strong coherency and continuity in the seismic section, reflective structures in a hardrock environment are typically less continuous. In order to image the internal structure of the mineralization and decipher the surrounding structures, we applied the concept of reflection image spectroscopy to the data, which allows the imaging of wavelength‐specific characteristics within the reflective body. As a result, conjugate crossing faults around the mineralization can directly be imaged in a low‐frequency band while the internal structure was obtained within the high‐frequency bands.

Reflection seismic data were acquired within two field campaigns in the Blötberget, Ludvika mining area of central Sweden, for deep imaging of iron‐oxide mineralization that were known to extend down to 800–850 m depth. The two surveys conducted in years 2015 and 2016, one employing a seismic landstreamer and geophones connected to wireless recorders, and another one using cabled geophones and wireless recorders, aimed to delineate the geometry and depth extent of the iron‐oxide mineralization for when mining commences in the area. Even with minimal and conventional processing approaches, the merged datasets provide encouraging information about the depth continuation of the mineralized horizons and the geological setting of the study area. Multiple sets of strong reflections represent a possible continuation of the known deposits that extend approximately 300 m further down‐dip than the known 850 m depth obtained from historical drilling. They show excellent correlation in shape and strength with those of the Blötberget deposits. Furthermore, several reflections in the footwall of the known mineralization can potentially be additional resources underlying the known ones. The results from these seismic surveys are encouraging for mineral exploration purposes given the good quality of the final section and fast seismic surveys employing a simple cost‐effective and easily available impact‐type seismic source.

Abstract. Many metallic mineral deposits have sufficient physical property contrasts, particularly density, to be detectable using seismic methods. These deposits are sometimes significant for our society and economic growth and can help to accelerate the energy transition towards decarbonization. However, their exploration at depth requires high-resolution and sensitive methods. Following a series of 2D seismic trials, a sparse, narrow source–receiver azimuth, 3D seismic survey was conducted in the Blötberget mine, in central Sweden, covering an area of approximately 6 km2 for deep-targeting iron oxide deposits and their host rock structures. The survey benefited from a collaborative work by putting together 1266 seismic recorders and a 32 t vibrator, generating 1056 shot points in a fixed geometry setup. Shots were fired at every 10 m where possible, and receivers were placed at every 10–20 m. Notable quality data were acquired despite the area being dominated by swampy places as well as by built-up roads and historical tailings. The data processing had to overcome these challenges for the static corrections and strong surface waves in particular. A tailored for hardrock setting and processing workflow was developed for handling such a dataset, where the use of mixed 2D and 3D refraction static corrections was relevant. The resulting seismic volume is rich in terms of reflectivity, with clear southeast-dipping reflections originating from the iron oxide deposits extending vertically and laterally at least 300 m beyond what was known from available boreholes. As a result, we estimate potential additional resources from the 3D reflection seismic experiment on the order of 10 Mt to be worth drilling for detailed assessments. The mineralization is crosscut by at least two major sets of northwest-dipping reflections interpreted to dominantly be normal faults and to be responsible for much of the lowland in the Blötberget area. Moreover, these post-mineralization faults likely control the current 3D geometry of the deposits. Curved and submerged reflections interpreted from folds or later intrusions are also observed, showing the geological complexity of the study area. The seismic survey also delineates the near-surface expression of a historical tailing as a by-product of refraction static corrections, demonstrating why 3D seismic data are so valuable for both mineral exploration and mine planning applications.

No abstract

To be fully embraced into mineral exploration, seismic data require to be acquired fast, cheaper and with minimum environmental impacts addressing also the often brown-field highly noisy environment where these surveys are employed. Since 2013 and through a number of case studies, we have been testing a newly developed for urban environment, digital-based 240 m long, seismic landstreamer for mine planning and mineral exploration purposes. Here, we present a pilot study examining the potential of the streamer for deep targeting a known, down to approximately 850 m depth, iron-oxide mineralization in the Bergslagen mineral district of central Sweden. Combined streamer (100-3C-MEMS (micro-electromechanical system), 2–4 m spacing) and 75 wireless recorders (mixed 10 Hz and MEMS, 10 m spacing) were used. A Bobcat-mounted drophammer, 500 kg, was used to generate the seismic signal. Within 4 days, approximately 3.5 km of seismic data using 2–10 m source and receiver spacing were acquired. Reflection data processing results clearly image the mineralization as a set of strong high-amplitude reflections and likely slightly extending beyond the known 850 m depth. This is encouraging and suggests such a cost-effective exploration method can be used in the area and elsewhere to delineate similar depth range iron-oxide deposits.