An acceleration sensor is an essential component of the vibration measurement, while the passivity and sensitivity are the pivotal features for its application. Here, we report a self-powered and highly sensitive acceleration sensor based on a triboelectric nanogenerator composed of a liquid metal mercury droplet (LMMD) and nanofiber-networked polyvinylidene fluoride (nn-PVDF) film. Due to the ultrahigh surface-to-volume ratio of nn-PVDF film and high surface tension, high mass density, high elastic as well as mechanical robustness of LMMD, the open-circuit voltage and short-circuit current reach up to 15.5 V and 300 nA at the acceleration of 60 m/s, respectively. The acceleration sensor has a wide detection range from 0 to 60 m/s with a high sensitivity of 0.26 V·s/m. Also, the output voltage and current show a negligible decrease over 200,000 cycles, evidently presenting excellent stability. Moreover, a high-speed camera was employed to dynamically capture the motion state of the acceleration sensor for insight into the corresponding work mechanism. Finally, the acceleration sensor was demonstrated to measure the vibration of mechanical equipment and human motion in real time, which has potential applications in equipment vibration monitoring and troubleshooting.

Flexible photodetectors (PDs) are attracting more attention due to their promising applications in wearable optoelectronic devices, bendable imaging sensors, and implantable optoelectronics. For the easy‐processable technology of massively fabricating PDs, instead of the expensive and complex high‐vacuum technique, the well‐matched work function of their active materials is essential. Herein, all‐sprayed‐processable and large‐area PDs are demonstrated on common paper based on two‐dimensional (2D) CsPbBr3 nanosheets and conductive Ti3C2Tx (MXene). Ascribed to the superior conductivity of MXene, high crystallinity of 2D CsPbBr3, and their well‐matched work function, the as‐prepared PDs exhibit an outstanding on/off current ratio up to 2.3 × 103 and a remarkable photoresponse as fast as 18 ms. Specifically, the detectivity (D*) of 6.4 × 108 Jones and responsivity (R) of 44.9 mA W−1 under a bias of 10 V are achieved. Besides, after bending 1500 cycles, the as‐prepared PDs can still maintain the excellent flexibility and stability. Based on this, a superior‐quality and large‐area 1665 pixel sensor in 72 cm2 (≈24 units cm−2) is developed, and it can clearly transmit the image of “0” to realize the photocommunication function. This work provides a low‐cost method of massively producing the flexible large‐area PDs for wearable optoelectronic devices and expanded photocommunication.

Low photoluminescence quantum yield (PLQY) and spectra instability, the two most difficult challenges in blue-emitting CsPbBr x Cl 3−x NCs, have not yet been solved. Quickly controlling the reaction thermodynamics is crucial to enhance crystallinity, thus PLQY and spectra stability, but it has been ignored until now. An ultrafast thermodynamic control (UTC) strategy is designed by utilizing liquid nitrogen to instantaneously freeze the superior crystal lattices of CsPbBr x Cl 3−x NCs formed at high temperature. The average cooling rate exhibits a 33-fold increase compared to conventional ice-water cooling (from 1.5 to 50 K s −1 ). This UTC can make the reaction thermodynamic energy of the system lower than the threshold very quickly. Therefore, abrupt termination of further crystal growth can be achieved, which also avoids additional nucleation at low temperature. With the assist of defect passivation, the final blue-emitting CsPbBr x Cl 3−x NCs exhibit an absolute PLQY of 98%, representing the highest value in Pb-based blue perovskites to date. More importantly, they exhibit superior spectra instability. This UTC strategy not only represents a new avenue to synthesize perovskite NCs with excellent crystal quality and ultrahigh PLQY, but also provides a good reference to deal with the recognized bottleneck of spectra instability.

No abstract

All-inorganic cesium lead halide (CsPbX 3 , X = Cl, Br, and I) perovskite nanocrystals (NCs) have gained increasing attention in recent years, due to their excellent optical and electronic properties that are critical in the fabrication of efficient optoelectronic [1] and photovoltaic devices. [2] Currently, the external quantum efficiency (EQE) of perovskite light-emitting diodes (LEDs) has exceeded 20% [1d,e] while the perovskite solar cells have recently reached a power conversion efficiency (PCE) of 23.7%. [3] However, the major obstacle to future commercialization of perovskite NCs is their inherent vulnerability due to their ionic nature. [4] Therefore, perovskite NCs will decompose fast when exposed to ambient, especially in the presence of water or even in a moist environment. [5] But the appearance of water is inevitable during the process of materials synthesis and devices fabrication, which will badly influence the device stability and performance. So, the intrinsic water stability improvement of all-inorganic perovskite plays a key role to effectively enhance the long-time stability of perovskite materials and enormously promote the commercial applications of perovskite-based optoelectronic and photovoltaic devices.To overcome the poor water stability of perovskite NCs arising from their intrinsically high ionic character, many strategies have been developed. Typically, the substitution of the more stable ligands for the commonly used oleic acid (OA) and oleylamine (OLA) can suppress the degradation and maintain the crystal structures in water or other polar solvent. [6] In addition, polymer materials can effectively encapsulate perovskite NCs and avoid them directly contact with the external environment, which ensure the high environment stability especially superior water resistance of the peovskite-polymer composites. [7] Moreover, embedding perovskite NCs into inorganic matrix such as ionic salt, metallic oxide and silica also can obtain relatively ideal environment stability. [8] Although all of these works remarkably enhance the water stability of perovskite materials, these strategies mainly focus on isolating the materials from the external environment but not intrinsically improving its water stability. And also, these isolated materials will have a negative effect on charge transfer ability. Therefore, to develop the novel perovskite materials with both long-term intrinsic water stability and good charge transport ability is extremely urgent for optoelectronic and photovoltaic devices.All-inorganic cesium lead halide perovskite nanocrystals (NCs) have emerged as attractive optoelectronic materials due to the excellent optical and electronic properties. However, their environmental stability, especially in the presence of water, is still a significant challenge for their further commercialization. Here, ultrahigh intrinsically water-stable all-inorganic quasi-2D CsPbBr 3 nanosheets (NSs) via aqueous phase exfoliation method are reported. Compared to conventional perovskite NCs, these u...