We present in this paper a novel fully decoupled silicon micromachined tri-axis linear vibratory gyroscope. The proposed gyroscope structure is highly symmetrical and can be limited to an area of about 8.5 mm × 8.5 mm. It can differentially detect three axes’ angular velocities at the same time. By elaborately arranging different beams, anchors and sensing frames, the drive and sense modes are fully decoupled from each other. Moreover, the quadrature error correction and frequency tuning functions are taken into consideration in the structure design for all the sense modes. Since there exists an unwanted in-plane rotational mode, theoretical analysis is implemented to eliminate it. To accelerate the mode matching process, the particle swam optimization (PSO) algorithm is adopted and a frequency split of 149 Hz is first achieved by this method. Then, after two steps of manual adjustment of the springs’ dimensions, the frequency gap is further decreased to 3 Hz. With the help of the finite element method (FEM) software ANSYS, the natural frequencies of drive, yaw, and pitch/roll modes are found to be 14,017 Hz, 14,018 Hz and 14,020 Hz, respectively. The cross-axis effect and scale factor of each mode are also simulated. All the simulation results are in good accordance with the theoretical analysis, which means the design is effective and worthy of further investigation on the integration of tri-axis accelerometers on the same single chip to form an inertial measurement unit.

In this paper, we present two design methods to improve the performance of disk resonator gyroscope (DRG), including decreasing the frequency split and increasing the quality factor (Q). The structure parameters, which can affect the frequency split and Q value were concluded with the help of the FEM software. Meanwhile, devices with different parameters were designed, fabricated, and tested, and the experimental result was in accordance with the simulation. With the proposed methods, the DRG was selected with a high Q value and a low frequency split to satisfy the demand of high performance. The weakness and future works were pointed at last.

In the process of motor rotation, the vibration caused by the rotor mass eccentricity seriously affects the dynamic characteristics and safety operation of system. So rotor mass eccentricity vibration compensation control on rotating machine has great significance, especially for the high speed bearing less induction motor (BIM). A rotor mass eccentricity compensation control strategy was presented to restrain the vibration of suspended rotor for BIM. Firstly, the suspension rotor dynamical model was deduced and unbalanced vibration mechanism was analyzed. Secondly, based on decoupling control between electromagnetic torque and radial force, the obtained vibration signal from the displacement sensor was put into the original radial force control system. Then, a feedforward compensator was set up to increase the same period component of the given radial force signal and enlarge the stiffness of the vibration signal. Finally, the compensation control of rotor vibration was realized by forcing the rotor shaft rotation around its geometric center. The simulation results show that the presented feedforward compensator can suppress the vibration of rotor under different speed and improve the precision of rotor suspension. The further experimental results also show that the control method can obviously reduce the peak-peak value of rotor radial displacement and effectively restrain rotor vibration.

To avoid the oscillation of four unequal masses seen in previous triaxial linear gyroscopes, a modified silicon triaxial gyroscope with a rotary wheel is presented in this paper. To maintain a large sensitivity and suppress the coupling of different modes, this novel gyroscope structure is designed be perfectly symmetrical with a relatively large size of about 9.8 mm × 9.8 mm. It is available for differentially detecting three-axis angular rates simultaneously. To overcome the coupling between drive and sense modes, numerous necessary frames, beams, and anchors are delicately figured out and properly arranged. Besides, some frequency tuning and feedback mechanisms are addressed in the case of post processing after fabrication. To facilitate mode matched function, a new artificial fish swarm algorithm (AFSA) performed faster than particle swarm optimization (PSO) with a frequency split of 108 Hz. Then, by entrusting the post adjustment of the springs dimensions to the finite element method (FEM) software ANSYS, the final frequency splits can be below 3 Hz. The simulation results demonstrate that the modal frequencies in drive and different sense modes are respectively 8001.1, 8002.6, 8002.8 and 8003.3 Hz. Subsequently, different axis cross coupling effects and scale factors are also analyzed. The simulation results effectively validate the feasibility of the design and relevant theoretical calculation.

No abstract