A short overview of composite materials for wind turbine applications is presented here. Requirements toward the wind turbine materials, loads, as well as available materials are reviewed. Apart from the traditional composites for wind turbine blades (glass fibers/epoxy matrix composites), natural composites, hybrid and nanoengineered composites are discussed. Manufacturing technologies for wind turbine composites, as well their testing and modelling approaches are reviewed.

This study shows that diazotized β-cyclodextrin (β-CD) can be produced, isolated, and immobilized onto glassy carbon and gold surfaces. 4-(1,2,3-Triazol-4-yl)benzenediazonium-β-CD tetrafluoroborate (pDz-β-CD) and 3-(1,2,3-triazol-4-yl)benzenediazonium-β-CD tetrafluoroborate (mDz-β-CD) were successfully prepared by Cu((I))-catalyzed azide alkyne coupling (CuAAC) of 6-monodeoxy-6-monoazido-β-cyclodextrin (N(3)-β-CD) and 4-ethynylaniline and 3-ethynylaniline, respectively, followed by diazotization. The products were isolated and stored successfully for several months at -18 °C. The intermediates and products were verified by Attenuated Total Reflectance Fourier Transform Infrared, Nuclear Magnetic Resonance, and Heteronuclear Single Quantum Coherence. pDz-β-CD and mDz-β-CD were immobilized onto glassy carbon and gold surfaces facilitated by electrochemical reduction of the diazonium group. The thus generated aryl radical reacted with the surface. The modified gold surfaces were investigated by Polarization Modulation Infrared Reflection Absorption Spectroscopy and cyclic voltammetry employing the redox probe K(3)Fe(CN)(6) to analyze the extent of blocking of the surfaces. Finally, the availability of the cavity of surface-immobilized β-CD was shown by complexation of ferrocene followed by cyclic voltametric analysis.

The interfacial shear strength (IFSS) is commonly used for evaluating the adhesion at the interface between fibre and matrix. A glass fibre/epoxy matrix system was investigated. The surface coatings applied to glass fibres may result in a discrepancy in the amine:epoxide group ratio between the interface and the bulk matrix, consequently moving the ratio away from the optimum stoichiometric ratio most often used. The amine:epoxide group ratio in the matrix was varied to obtain the optimum ratio at the interface. The study found that the amine:epoxide ratio influenced the IFSS with an optimum just below the stoichiometric ratio. The microbond test was conducted in a thermal mechanical analyser (TMA) to determine the IFSS thus revealing an inverse dependency on the testing temperature: an increased testing temperature yields a decrease of IFSS. IFSS determined at temperatures below the glass transition temperature displays a decreasing trend at high amine:epoxide ratio whereas IFSS measured at testing temperatures above the glass transition temperature steadily increases as the amine:epoxide ratio increases. The microbond test was conducted using both a tensile tester and a TMA setup. The two microbond test setups yielded results with same behaviour of the IFSS as a function of the amine:epoxide ratio.

The influence of removing sizing on strength and stiffness of conventional and high modulus E-glass fibres Abstract. Two types of E-glass fibres, a conventional and a high modulus where the last one in the following will be denoted as ECR-glass fibre, were investigated regarding density, diameter, stiffness and strength. The fibres were analysed as pristine and after sizing removal treatments. The sizing was removed by either burning at 565• C or soxhlet extraction with acetone. It was found that the density and the stiffness increased after removing the sizing by the two removal treatments whereas the diameter did not change significantly. The strength of the fibres decreased after burning as the sizing, protecting against water and fibre-fibre damage, had been removed. The strength of the fibres after extraction was not significantly different from the strength of the pristine fibres despite removing the sizing. This indicates that the bonded part of sizing is still protecting the glass fibre surface.