No abstract

Dual tires have traditionally been used to limit pavement damage by efficiently distributing axle loads over a larger contact area than single tires. However, in recent years, the trucking industry, stating economic and safety benefits, has promoted the use of wide-base single tires. The Super Single tire, an early type of wide-base tire, proved inadequate and induced excessive pavement damage. By contrast, the new generation wide-base tires have contact areas that approach those of dual tires and offer the potential for improved performance. The Florida Department of Transportation investigated the pavement damage potential of four tire types, including a conventional dual tire (11R22.5), a Super Single (425/65R22.5), and two newly designed wide-base single tires (445/50R22.5 and 455/55R22.5 respectively). A controlled accelerated pavement testing program, in addition to theoretical modeling, was performed to determine critical pavement response parameters. Pavement damage was measured in terms of rutting and fatigue cracking (bottom-up or top-down), the predominant distresses in Florida. The investigation revealed that the 455-mm wide-base tire performed as well as the dual tire. By comparison, the 445-mm wide-base tire was shown to create more rut damage on a dense-graded pavement surface and was predicted to create more bottom-up cracking than a dual tire. As expected, the Super Single induced the most damage to the pavement.

In 2010 a theoretical approach to the evaluation and specification of aggregate gradations to resist rutting was evaluated by the Florida Department of Transportation by accelerated pavement testing. This approach, known as the dominant aggregate size range (DASR) gradation model, provides a framework to ensure that the coarse aggregate of the resulting mixture has sufficient aggregate interlock to resist permanent deformation. Further research by the University of Florida and the Department of Transportation found that the properties of the interstitial components (ICs) within the DASR voids were strongly related to the durability and fracture resistance of asphalt mixtures. Parameters that made up the combined DASR-IC model included the DASR porosity, disruption factor (DF), effective film thickness (EFT), and fine aggregate ratio (FAR). The original evaluation of the DASR model was recently extended to include DASR gradations that might have had marginal aggregate interlock (i.e., marginal DASR porosity) and the effect of IC properties on mixture fracture resistance. The results confirmed that the rutting performance of the asphalt mixture was primarily controlled by the DASR porosity and that mixtures with marginal DASR porosity might still have had significantly better rutting performance than mixtures with poor DASR porosity. In addition, it was shown that the DASR porosity, DF, EFT, and FAR parameters played a critical role in mixture cracking performance. The validation of the combined DASR–IC model was documented, and the acceptable range of each parameter for improved mixture rutting and cracking performance was confirmed.

A full-scale precast prestressed concrete pavement (PPCP) system was constructed and evaluated under actual traffic load conditions to develop the design guideline under Florida conditions. This test section showed good load transfer efficiency and riding quality. However, information was lacking about its structural response and potential performance. A three-dimensional finite element model was developed for stress analysis of PPCP under critical loading conditions. The developed three-dimensional model was calibrated by using deflection data obtained with a falling weight deflectometer. The model was used to perform a parametric analysis to determine the effects of critical loading location, concrete modulus, coefficient of thermal expansion of concrete, loss of prestress force, and subgrade stiffness under typical Florida conditions. Results of the parametric study indicate that the maximum stresses in the concrete increased significantly as the concrete modulus and coefficient thermal expansion increased. Because of the increase in flexural strength associated with the increase in elastic modulus of the concrete, an increase in elastic modulus of the concrete results in a decrease in the computed stress-to-strength ratio under critical load–temperature conditions. The PPCP system that was evaluated appeared to have a good predicted pavement performance with a computed stress-to-strength ratio of less than 0.5, with up to an additional loss of 20% of prestress force in the longitudinal and transverse directions. Variations in the base and subbase properties were found to have a minimal effect on the maximum induced stresses in concrete. This finding indicates that the PPCP system is appropriate for a wide variety of subbase and subgrade conditions.

No abstract