We present a practical implementation of calibration-free wavelength-modulation spectroscopy with second harmonic detection (WMS-2f) for measurements of gas temperature and concentration in harsh environments. The method is applicable to measurements using lasers with synchronous wavelength and intensity modulation (such as injection current-tuned diode lasers). The key factors that enable measurements without the on-site calibration normally associated with WMS are (1) normalization of the WMS-2f signal by the first harmonic (1f) signal to account for laser intensity, and (2) the inclusion of laser-specific tuning characteristics in the spectral-absorption model that is used to compare with measured 1f-normalized, WMS-2f signals to infer gas properties. The uncertainties associated with the calibration-free WMS method are discussed, with particular emphasis on the influence of pressure and optical depth on the WMS signals. Many of these uncertainties are also applicable to calibrated WMS measurements. An example experimental setup that combines six tunable diode laser sources between 1.3 and 2.0 mum into one probe beam for measurements of temperature, H(2)O, and CO(2) is shown. A hybrid combination of wavelength and frequency demultiplexing is used to distinguish among the laser signals, and the optimal set of laser-modulation waveforms is presented. The system is demonstrated in the harsh environment of a ground-test scramjet combustor. A comparison of direct absorption and 1f-normalized, WMS-2f shows a factor of 4 increase in signal-to-noise ratio with the WMS technique for measurements of CO(2) in the supersonic flow. Multidimensional computational fluid-dynamics (CFD) calculations are compared with measurements of temperature and H(2)O using a simple method that accounts for the influence of line-of-sight (LOS) nonuniformity on the absorption measurements. The comparisons show the ability of the LOS calibration-free technique to gain useful information about multidimensional CFD models.
Infrared laser-absorption spectroscopy (IR-LAS) sensors play an important role in diagnosing and characterizing a wide range of combustion systems. Of all the laser-diagnostic techniques, LAS is arguably the most versatile and quantitative, as it has been used extensively to provide quantitative, species-specific measurements of gas temperature, pressure, composition and velocity in both laboratory-and industrial-scale systems. Historically, most IR-LAS work has been conducted using tunable diode lasers, however, today's researchers have access to a wide range of light sources that provide unique sensing capabilities and convenient access to nearly the entire IR spectrum (≈1 to 20 μm). In particular, the advent of room-temperature wavelength-tunable mid-infrared semiconductor lasers (e.g., interband-and quantum-cascade lasers) and hyperspectral light sources (e.g., Fourierdomain mode-locked lasers, dispersed supercontinuum lasers, and frequency combs) has provided a number of unique capabilities that combustion researchers have exploited. The primary goal of this review paper is to document the recent development, application, and current capabilities of IR-LAS sensors for laboratory-and industrial-scale combustors and propulsion systems. A thorough review and description of the fundamental spectroscopy governing the accuracy of such sensors, and recent findings and databases that enable improved modeling of molecular absorption spectra will be provided. Modern light sources and the most commonly used diagnostic techniques are also discussed.
Tunable diode laser absorption measurements at high pressures by use of wavelength-modulation spectroscopy (WMS) require large modulation depths for optimum detection of molecular absorption spectra blended by collisional broadening or dense spacing of the rovibrational transitions. Diode lasers have a large and nonlinear intensity modulation when the wavelength is modulated over a large range by injection-current tuning. In addition to this intensity modulation, other laser performance parameters are measured, including the phase shift between the frequency modulation and the intensity modulation. Following published theory, these parameters are incorporated into an improved model of the WMS signal. The influence of these nonideal laser effects is investigated by means of wavelength-scanned WMS measurements as a function of bath gas pressure on rovibrational transitions of water vapor near 1388 nm. Lock-in detection of the magnitude of the 2f signal is performed to remove the dependence on detection phase. We find good agreement between measurements and the improved model developed for the 2f component of the WMS signal. The effects of the nonideal performance parameters of commercial diode lasers are especially important away from the line center of discrete spectra, and these contributions become more pronounced for 2f signals with the large modulation depths needed for WMS at elevated pressures.
The development and initial demonstration of a scanned-wavelength, first-harmonic-normalized, wavelength-modulation spectroscopy with nf detection (scanned-WMS-nf/1f) strategy for calibration-free measurements of gas conditions are presented. In this technique, the nominal wavelength of a modulated tunable diode laser (TDL) is scanned over an absorption transition to measure the corresponding scanned-WMS-nf/1f spectrum. Gas conditions are then inferred from least-squares fitting the simulated scanned-WMS-nf/1f spectrum to the measured scanned-WMS-nf/1f spectrum, in a manner that is analogous to widely used scanned-wavelength direct-absorption techniques. This scanned-WMS-nf/1f technique does not require prior knowledge of the transition linewidth for determination of gas properties. Furthermore, this technique can be used with any higher harmonic (i.e., n>1), modulation depth, and optical depth. Selection of the laser modulation index to maximize both signal strength and sensitivity to spectroscopic parameters (i.e., gas conditions), while mitigating distortion, is described. Last, this technique is demonstrated with two-color measurements in a well-characterized supersonic flow within the Stanford Expansion Tube. In this demonstration, two frequency-multiplexed telecommunication-grade TDLs near 1.4 μm were scanned at 12.5 kHz (i.e., measurement repetition rate of 25 kHz) and modulated at 637.5 and 825 kHz to determine the gas temperature, pressure, H2O mole fraction, velocity, and absorption transition lineshape. Measurements are shown to agree within uncertainty (1%-5%) of expected values.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.