Lithium metal is one of the most attractive anode materials for next-generation lithium batteries due to its high specific capacity and low electrochemical potential. However, the poor cycling performance and serious safety hazards, caused by the growth of dendritic and mossy lithium, has long hindered the application of lithium metal based batteries. Herein, we reported a rational design of free-standing Cu nanowire (CuNW) network to suppress the growth of dendritic lithium via accommodating the lithium metal in three-dimensional (3D) nanostructures. We demonstrated that as high as 7.5 mA h cm(-2) of lithium can be plated into the free-standing copper nanowire (CuNW) current collector without the growth of dendritic lithium. The lithium metal anode based on the CuNW exhibited high Coulombic efficiency (average 98.6% during 200 cycles) and outstanding rate performance owing to the suppression of lithium dendrite growth and high conductivity of CuNW network. Our results demonstrate that the rational nanostructural design of current collector could be a promising strategy to improve the performance of lithium metal anode enabling its application in next-generation lithium-metal based batteries.

All-inorganic lead halide perovskite nanocrystals (NCs) are potential candidates for fabricating high-performance light-emitting diodes (LEDs) owing to their precisely tunable bandgaps, high photoluminescence (PL) efficiency, and excellent color purities. However, the performance of pure red (630−640 nm) all-inorganic perovskite LEDs is still limited by the halide segregation-induced instability of the electroluminescence (EL) of mixed halide CsPbI 3-x Br x NCs. Herein, we report an effective approach to improving the EL stability of pure red all-inorganic CsPbI 3-x Br x NC-based LEDs via the passivation of potassium bromide on NCs. By adding potassium oleate to the reaction system, we obtained potassium bromide surfacepassivated (KBr-passivated) CsPbI 3-x Br x NCs with pure red PL emission and a photoluminescence quantum yield (PLQY) exceeding 90%. We determine that most potassium ions present on the surface of NCs bind with bromide ions and thus demonstrate that potassium bromide surface passivation of NCs can both improve the PL stability and inhibit the halide segregation of NCs. Using KBr-passivated CsPbI 3-x Br x NCs as an emitting layer, we fabricated stable and pure red perovskite LEDs with emission at 637 nm, showing a maximum brightness of 2671 cd m −2 , maximum external quantum efficiency of 3.55%, and good EL stability. The proposed KBrpassivated NC strategy will open a new avenue for fabricating efficient, stable, and tunable pure color perovskite NC LEDs.

Metal halide perovskites are promising semiconductors for next-generation light-emitting diodes (LEDs) due to their high luminance, excellent color purity, and handily tunable band gap. However, it remains a great challenge to develop perovskite LEDs (PeLEDs) with pure red emission at the wavelength of 630 nm. Herein, we report a spectrally stable and efficient pure red PeLED by employing sequential ligand posttreated CsPbI 3 quantum dots (QDs). The synthesized CsPbI 3 QDs with a size of ∼5 nm are treated in sequential steps using the ligands of 1-hydroxy-3-phenylpropan-2-aminium iodide (HPAI) and tributylsulfonium iodide (TBSI), respectively. The CsPbI 3 QD films exhibit improved optoelectronic properties, which enables the fabrication of a pure red PeLED with a peak external quantum efficiency (EQE) of 6.4% and a stable EL emission centered at the wavelength of 630 nm. Our reported sequential ligand posttreatment strategy opens a new route to improve the stability and efficiency of PeLEDs based on QDs.