Column percolation tests may be suitable for prediction of chemical leaching from soil and soil materials. However, compared with batch leaching tests, they are time-consuming. It is therefore important to investigate ways to shorten the tests without affecting the quality of results. In this study, we evaluate the feasibility of decreasing testing time by increasing flow rate and decreasing equilibration time compared to the conditions specified in ISO/TS 21268-3, with equilibration periods of 48h and flow rate of 12mL/h. We tested three equilibration periods (0, 12-16, and 48h) and two flow rates (12 and 36mL/h) on four different soils and compared the inorganic constituent releases. For soils A and D, we observed similar values for all conditions except for the 0h-36mL/h case. For soil B, we observed no appreciable differences between the tested conditions, while for soil C there were no consistent trends probably due to the difference in ongoing oxidation reactions between soil samples. These results suggest that column percolation tests can be shortened from 20 to 30days to 7-9days by decreasing the equilibration time to 12-16h and increasing the flow rate to 36mL/h for inorganic substances.

No abstract

Soil leaching tests are commonly used to evaluate the leachability of hazardous materials, such as heavy metals, from the soil. Batch leaching tests often enhance soil colloidal mobility and may require solid-liquid separation procedures to remove excess soil particles. However, batch leaching test results depend on particles that can pass through a 0.45μm membrane filter and are influenced by test parameters such as centrifugal intensity and filtration volume per filter. To evaluate these parameters, we conducted batch leaching experiments using metal-contaminated soils and focused on the centrifugal intensity and filtration volume per filter used in solid-liquid separation methods currently employed in standard leaching tests. Our experiments showed that both centrifugal intensity and filtration volume per filter affected the reproducibility of batch leaching tests for some soil types. The results demonstrated that metal concentrations in the filtrates significantly differed according to the centrifugal intensity when it was 3000 g for 2h or less. Increased filtration volume per filter led to significant decreases in filtrate metal concentrations when filter cakes formed during filtration. Comparison of the filtration tests using 0.10 and 0.45μm membrane filters showed statistically significant differences in turbidity and metal concentration. These findings suggest that colloidal particles were not adequately removed from the extract and contributed substantially to the apparent metal concentrations in the leaching test of soil containing colloidal metals.

Studies on the formation of polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) during the electrolysis of sodium chloride solution (brine) using graphite or titanium electrodes were carried out at a laboratory scale. High concentrations of PCDFs but no PCDDs were formed in tests using graphite electrodes. With titanium electrodes, PCDFs were only formed when tar pitch was added and mainly originated from the dibenzofuran present in the tar. For the first time, a detailed assessment of the formation of mono- to octachlorinated PCDD/PCDF from tar pitch was investigated. The assessment included of the chlorination steps proved that PCDFs were formed by successive lateral chlorinated from dibenzofuran to MonoCDFs, DiCDFs, and TriCDFs to form the typical known "chlorine pattern" of TetraCDF to OctaCDF with a dominance of 1,2,7,8- and 2,3,7,8-TetraCDFs, 1,2,3,7,8-PentaCDF, and 1,2,3,4,7,8-HexaCDF as marker congeners. The final homologue distributions depended on reaction time and reaction temperature. In addition, electrolysis with non-chlorinated dibenzo-p-dioxins, dibenzofuran, and biphenyl was carried out. As a result, PCDDs, PCDFs, and PCB were formed at comparable yields. Congener patterns in soil samples from a PCDD/F-contaminated site where chlor-alkali electrolysis had been operated for decades in Japan had identical isomer distribution demonstrating the source and contamination potential and risk of these processes. Therefore, sites where in the past 120 years chlor-alkali electrolysis has been operated or where residues from chlor-alkali production or other chlorine using industries have been disposed should be assessed for their pollution level and exposure relevance. The assessment of total organohalogen content revealed that PCDF is only a small fraction of organohalogens in the contaminated soils. For an appropriate risk assessment, also other chlorinated aromatic compounds such as PCBs or PCNs need to be considered.

No abstract