We have developed an enhanced Littrow configuration extended cavity diode laser ͑ECDL͒ that can be tuned without changing the direction of the output beam. The output of a conventional Littrow ECDL is reflected from a plane mirror fixed parallel to the tuning diffraction grating. Using a free-space Michelson wavemeter to measure the laser wavelength, we can tune the laser over a range greater than 10 nm without any alteration of alignment.

Eyjafjallajökull, a volcano in southern Iceland, erupted explosively in April and May 2010 depositing ash over a region of more than 3000 km2 to the east and southeast of the volcano. This deposited ash has been frequently remobilized by the wind causing concern for the health of Icelanders living in the region. An investigation was carried out to determine whether it would be possible to produce forecasts of days when high airborne ash concentrations were likely to occur. Information about the spatially varying surface characteristics of the region of deposited ash is not available so in the modeling approach adopted here ash is released from the surface at a rate proportional to the cube of the excess friction velocity (local friction velocity minus a threshold) only when the friction velocity exceeds a threshold. Movement of the resuspended ash is then modeled in a Lagrangian dispersion model. Modeled ash concentrations are compared to observed concentrations from two periods; PM10 observations between 23 May and 2 July 2010 and airborne particle counts between 21 September 2010 and 16 February 2011. More than 66% of the resuspension episodes between May and July are captured by the model and the relative magnitudes of the modeled episodes in this period are in good agreement with the observations. 66% of episodes between October and February are also captured by the model although there is an increase in the false alarm rate which appears to be due to the influence of precipitation.

Modeling the transport of volcanic ash and gases released during volcanic eruptions is crucially dependent on knowledge of the source term of the eruption, that is, the source strength as a function of altitude and time. For the first time, an inversion method is used to estimate the source terms of both volcanic sulfur dioxide (SO 2 ) and ash. It was applied to the explosive volcanic eruption of Grímsvötn, Iceland, in May 2011. The method uses input from the particle dispersion model, FLEXPART (flexible particle dispersion model), a priori source estimates, and satellite observations of SO 2 or ash total columns from Infrared Atmospheric Sounding Interferometer to separately obtain the source terms for volcanic SO 2 and fine ash. The estimated source terms show that SO 2 was emitted mostly to high altitudes (5 to 13 km) during about 18 h (22 May, 00-18 UTC) while fine ash was emitted mostly to low altitudes (below 4 km) during roughly 24 h (22 May 06 UTC to 23 May 06 UTC). FLEXPART simulations using the estimated source terms show a clear separation of SO 2 (transported mostly northwestward) and the fine ash (transported mostly southeastward). This corresponds well with independent satellite observations and measured aerosol mass concentrations and lidar measurements at surface stations in Scandinavia. Aircraft measurements above Iceland and Germany confirmed that the ash was located in the lower atmosphere. This demonstrates that the inversion method, in this case, is able to distinguish between emission heights of SO 2 and ash and can capture resulting differences in transport patterns.

Because of the potential impact on agriculture and other key human activities, efforts have been dedicated to the local control of precipitation. The most common approach consists of dispersing small particles of dry ice, silver iodide, or other salts in the atmosphere. Here we show, using field experiments conducted under various atmospheric conditions, that laser filaments can induce water condensation and fast droplet growth up to several μm in diameter in the atmosphere as soon as the relative humidity exceeds 70%. We propose that this effect relies mainly on photochemical formation of p.p.m.-range concentrations of hygroscopic HNO3, allowing efficient binary HNO3–H2O condensation in the laser filaments. Thermodynamic, as well as kinetic, numerical modelling based on this scenario semiquantitatively reproduces the experimental results, suggesting that particle stabilization by HNO3 has a substantial role in the laser-induced condensation.

No abstract