Produced water is the largest waste stream generated in oil and gas industries. It is a mixture of different organic and inorganic compounds. Due to the increasing volume of waste all over the world in the current decade, the outcome and effect of discharging produced water on the environment has lately become a significant issue of environmental concern. Produced water is conventionally treated through different physical, chemical, and biological methods. In offshore platforms because of space constraints, compact physical and chemical systems are used. However, current technologies cannot remove small-suspended oil particles and dissolved elements. Besides, many chemical treatments, whose initial and/or running cost are high and produce hazardous sludge. In onshore facilities, biological pretreatment of oily wastewater can be a cost-effective and environmental friendly method. As high salt concentration and variations of influent characteristics have direct influence on the turbidity of the effluent, it is appropriate to incorporate a physical treatment, e.g., membrane to refine the final effluent. For these reasons, major research efforts in the future could focus on the optimization of current technologies and use of combined physico-chemical and/or biological treatment of produced water in order to comply with reuse and discharge limits.

The difficulties associated with transportation and refining of crude oil emulsions as well as produced water discharge limitations are among the conspicuous clues that have led the oilfield researchers to probe into practical demulsification methods for many decades.Inconsistent research outcomes observed in the literature for a particular demulsification method of a typical emulsion (i.e., water-in-oil or oil-in-water) arise not only from the varied influential parameters associated (such as salinity, temperature, pH, dispersed phase content, emulsifier/demulsifier concentration, droplet size, etc.), but also from the diverse types of emulsion constituents (namely oil, surfactant, salt, alkali, polymer, fine solids, and/or other chemicals/impurities). Being the main component in formation of stabilizing interfacial film surrounding the dispersed phase droplets, surfactant is the most predominant contributor to emulsion stability, extent of which depends on its nature (being ionic or nonionic, and its degree of hydrophilicity/lipophilicity), concentration and interaction with other surface-active agents in the emulsion, as well as on the salinity, temperature, and pH of the system. In this paper, it is endeavored to overview some of the most commonly exploited demulsification techniques (i.e., chemical, biological, membrane, electrical, and microwave irradiation) on both the oilfield and synthetic emulsions, taking into account the emulsion-stabilizing anddestabilizing effects with regard to the dominant parameters plus the emulsion composition.Further, the variations occurring in interfacial properties of emulsions by demulsification process are discussed. Finally, the mechanism(s) involved in emulsions resolution achieved by each method is elucidated. Clearly, the most efficient demulsification approach is the one able to attain desirable separation efficiency while complying with the environmental regulations and imposing the least economic burden on the petroleum industry.

The threat of oil pollution increases with the expansion of oil exploration and production activities, as well as the industrial growth around the world. The study on the treatment of oily wastewater is a critical issue to the environmental protection as oil caused problems to the wastewater treatment facilities. Although oil particles can efficiently be removed by advanced technologies, the treatments are usually expensive and difficult to maintain. Adsorption and coalescence filtration are promising choice of treatment for its simplicity, effectiveness, and feasibility when appropriate sorbent is used. This review discusses the recent papers on the use of natural fibrous sorbent for removal of oil from wastewater, and its current development. With their excellent oil removal properties, environmental friendliness, easy availability, and feasibility, natural fibrous sorbents are an attractive alternative for oily wastewater treatment.

The dimensional stability and dynamic mechanical properties on bamboo (non woven mat)/kenaf (woven mat) hybrid composites was carried out in this study. The hybridization effect of bamboo (B) and kenaf (K) fibers at different weight ratio were studied at B:K:70:30, and B:K:30:70 while maintaining total fiber loading of 40% by weight. The coefficient of thermal expansion (CTE) and dynamic mechanical properties of composites were analyzed by thermomechanical anlayzer (TMA), and dynamic mechanical analyzer (DMA), respectively. Positive hybridization effects were observed on B:K:50:50 hybrid composite with lowest CTE and highest dynamic mechanical properties among all composites. The dimensional stability were strongly influence by the fiber orientation where all composites shows prominent expansion in the transverse fibers direction but relatively low expansion in longitudinal fibers direction. Dynamic mechanical properties in term of complex modulus (E*), storage modulus (E′), loss modulus (E″), Tan delta and Cole-Cole plot were studied. DMA results reveal that B:K:50:50 hybrid composite possess the highest complex modulus due to the strong fiber/matrix interfacial bonding which supported by the coefficient of effectiveness and Cole-Cole plot. Hence, it is concluded that 50:50 weight ratio of bamboo and kenaf fibers is the optimum mixing ratio to enhance both dimensional and dynamic mechanical properties of hybrid composites, and it can be utilized for automotive or building materials applications which demand high dimensional stability and dynamic mechanical properties.

No abstract