No abstract

Poly(3-hydroxybutyrate), P(3HB), produced from Bacillus cereus SPV using a simple glucose feeding strategy was used to fabricate P(3HB) microspheres using a solid-in-oil-water (s/o/w) technique. For this study, several parameters such as polymer concentration, surfactant and stirring rates were varied in order to determine their effect on microsphere characteristics. The average size of the microspheres was in the range of 2 μm to 1.54 μm with specific surface areas varying between 9.60 m2/g and 6.05 m2/g. Low stirring speed of 300 rpm produced slightly larger microspheres when compared to the smaller microspheres produced when the stirring velocity was increased to 800 rpm. The surface morphology of the microspheres after solvent evaporation appeared smooth when observed under SEM. Gentamicin was encapsulated within these P(3HB) microspheres and the release kinetics from the microspheres exhibiting the highest encapsulation efficiency, which was 48%, was investigated. The in vitro release of gentamicin was bimodal, an initial burst release was observed followed by a diffusion mediated sustained release. Biodegradable P(3HB) microspheres developed in this research has shown high potential to be used in various biomedical applications.

Bioglass(®)-based scaffolds for bone tissue engineering have been developed, which can also serve as carriers for drug delivery. For this, P(3HB) microspheres (PMSs) loaded with tetracycline were fabricated and immobilised on the scaffold surfaces by a modified slurry dipping technique. The sustained drug delivery ability in simulated body fluid was confirmed by using UV-Vis absorption spectroscopy measurements. The MTT assay using mouse fibroblast cells provided evidence that the tetracycline loaded microspheres produced in this study show limited cytotoxicity. The scaffolds developed in this work provide mechanical support, adequate 3D surface roughness, bioactivity and controlled drug delivery function, and are thus interesting candidates for bone tissue engineering applications.

Off-the-shelf availability of tissue-engineered skin constructs, tailored by different combinations of reagents to produce a highly preserved biological matrix is often the only means to help patients suffering skin damage. This study assessed the effect of five different decellularisation methods on porcine dermal scaffolds with regard to matrix composition, biomechanical strength, and cytotoxicity using an in vitro biocompatibility assay. Results demonstrated that four out of the five tested decellularisation protocols were efficient in producing acellular scaffolds. Nevertheless, decellularisation method using osmotic shock without enzymatic digestion showed to be efficient not only in removing cellular material and debris from dermal scaffolds but was also beneficial in the preservation of extracellular matrix components (glycosaminoglycans and collagen). Histological assessment revealed that the dermal architecture of coarse collagen bundles was preserved. Examinations by scanning electron microscopy and transmission electron microscopy showed that the arrangement and ultrastructure of collagen fibrils in the scaffolds were retained following non-enzymatic method of decellularisation and also after collagen crosslinking using genipin. Moreover, this decellularised scaffold was not only shown to be biologically compatible when co-cultured with bone marrow-derived mesenchymal stem cells and fibroblasts, but also stimulated the cells to release trophic factors essential for tissue regeneration.

Bioactive glass (BG) is considered an ideal material for haemostasis as it releases Ca 2+ ions upon hydration, which is required to support thrombosis. In this study the effect of the presence of the BG nanoparticles in P(3HB) microsphere films on the structural properties, thermal properties and biocompatibility of the films were studied. The nanoscaled bioactive glass with a high surface area was also tested for its in vitro haemostatic efficacy and was found to be able to successfully reduce the clot detection time. In an effort to study the effect of the roughness induced by the formation of HA on the cellular functions such as cell adhesion, cell mobility and cell differentiation, the composite films were immersed in SBF for a period of 1, 3 and 7 days. From the SEM images the surface of the P(3HB)/n-BG composite microsphere films appeared fairly uniform and smooth on day 1, however on day 3 and day 7 a rough and uneven surface was observed. The presence of HA on the composite microsphere films on day 3 and day 7 influenced the surface roughness of the films. However, when the P(3HB)/n-BG 2 composite microspheres with enhanced surface roughness were tested for biocompatibility, reduced amount of protein adsorption and cell adhesion were observed. This study thus revealed that there is an optimal surface roughness for the P(3HB) microsphere films for increased cell adhesion, beyond which it could be deleterious for cell adhesion and differentiation.