No abstract

A way to reduce net CO2 emission and circumvent the high particle emissions from compression ignition (CI) engines, while retaining high efficiency, is by utilizing lighter alcohols in the partially premixed combustion (PPC) process. Methanol and ethanol have a very short carbon chain, and form less soot/particulate matter (PM) during combustion compared to diesel fuel. This study analyzes and compares the characteristics of PM emissions from methanol, ethanol and diesel in terms of soot mass concentration, number concentration and particle size distribution in one cylinder of a six cylinder Scania D13 heavy duty (HD) engine under two operating loads; 6 bar and 10 bar gross mean indicated effective pressure (IMEPG). An electrostatic precipitator (ESP) was used to sample PM on copper grids for transmission electron microscopy (TEM) and energy dispersive X-ray analysis. Also, new and used lubrication oil together with methanol and diesel were analyzed for their sulphur and metal content.Nucleation mode and the majority of accumulation mode particles from methanol and ethanol combustion, showed mainly Ca, S, P and Zn in the energy dispersive X-ray spectrometry (EDX) analysis and were hypothesized to be emitted mainly from the lubrication oil rather than the combustion of the fuel itself. From diesel combustion, the accumulation mode particles were more abundant in comparison with the alcohols and PM/soot emissions measured with the photoacoustic technique were 3 to 10 times higher than for the alcohols. There were also fewer nucleation mode particles present; although they consisted of the same four abovementioned elements. Utilizing alcohols in CI engines have a great advantage regarding PM, particle number emissions and efficiency. However, the resulting nucleation mode particles need to be reduced to avoid future health concerns.

This study investigates particulate matter (PM) and regulated emissions from renewable rapeseed oil methyl ester (RME) biodiesel in pure and blended forms and contrasts that to conventional diesel fuel. Environmental and health concerns are the major motivation for combustion engines research, especially finding sustainable alternatives to fossil fuels and reducing diesel PM emissions. Fatty acid methyl esters (FAME), including RME, are renewable fuels commonly used from low level blends with diesel to full substitution. They strongly reduce the net carbon dioxide emissions. It is largely unknown how the emissions and characteristics of PM get altered by the combined effect of adding biodiesel to diesel and implementing modern engine concepts that reduce nitrogen oxides (NOx) emissions by exhaust gas recirculation (EGR). Therefore, the exhaust from a single-cylinder Scania D13 heavy-duty (HD) diesel engine fuelled with petroleum-based MK1 diesel, RME, and a 20% RME blend (B20), was sampled while the inlet oxygen concentration was stepped from ambient to very low by varying EGR. Regulated gaseous emissions, mass of total black carbon (BC) and organic aerosol (OA), particle size distributions and the soot nanostructure by means of transmission electron microscopy (TEM), were studied. For all EGR levels, RME showed reduced BC emissions (factor 2 for low and 3-4 for higher EGR) and total particulate number count (TPNC) compared with diesel and B20. B20 was closer to diesel than RME in emission levels. RME opens a significant possibility to utilise higher levels of EGR and stay in the region of low NOx, while not producing more soot than with diesel and B20. Adding EGR to 15% inlet O2 did not affect the nanostructure of PM. A difference between the fuels was noticeable: branched agglomerates of diesel and RME were composed of many primary particles, whereas those of B20 were more often "melted" together (necking).

Constraining the climate impact of particulate brown carbon (BrC) will require identification of formation mechanisms and isolation of its different components to allow for source apportionment. For fresh combustion aerosols, the light absorption characteristics and the Absorption Ångstrom Exponent (AAE) are principally controlled by the combustion conditions in which the particles formed and evolved. We investigated the influence of combustion temperatures on the BrC or black carbon (BC) emission characteristics for a miniCAST soot generator (propane fuel) and a modern heavyduty diesel engine (petroleum diesel and two renewable diesel fuels). Changes in the AAE, mass spectral signatures, and thermal-optical characteristics were studied. We show that changing operating parameters to gradually reduce the combustion temperatures in these two fundamentally different combustion devices result in a regression from BC dominated to BrC dominated particle emissions. The regression towards BrC was associated with: 1) an increasing mass fraction of particulate non-refractory polycyclic aromatic hydrocarbons (PAHs), 2) an increasing fraction of refractory organic carbon, 3) more curved soot nanostructures and shorter fringe lengths, and 4) increased signal from (refractory) large carbon fragments in IR laser-vaporization aerosol mass spectra. Based on these results we argue that fresh BrC dominated combustion aerosols are attributed to primary emissions from low temperature combustion, highlighting the influence of refractory constituents and soot nanostructure. Higher temperatures favor the growth of conjugated polyaromatic structures in the soot, a progression hypothesized to control the evolution from BrC to BC character of the emitted aerosols.

Abstract. We studied ice-nucleating abilities of particulate emissions from a modern heavy-duty diesel engine using three different types of fuel. The polydisperse particle emissions were sampled during engine operation and introduced to a continuous-flow diffusion chamber (CFDC) instrument at a constant relative humidity RHwater=110 %, while the temperature was ramped between −43 and −32 ∘C (T scan). The tested fuels were EN 590 compliant low-sulfur fossil diesel, hydrotreated vegetable oil (HVO), and rapeseed methyl ester (RME); all were tested without blending. Sampling was carried out at different stages in the engine exhaust aftertreatment system, with and without simulated atmospheric processing using an oxidation flow reactor. In addition to ice nucleation experiments, we used supportive instrumentation to characterize the emitted particles for their physicochemical properties and presented six parameters. We found that the studied emissions contained no significant concentrations of ice-nucleating particles likely to be of atmospheric relevance. The substitution of fossil diesel with renewable fuels, using different emission aftertreatment systems such as a diesel oxidation catalyst, and photochemical aging of total exhaust had only minor effect on their ice-nucleating abilities.