Articles you may be interested inEffect of WN content on toughness enhancement in V1−xWxN/MgO(001) thin films J. Vac. Sci. Technol. A 32, 030603 (2014); 10.1116/1.4867610Volatile and nonvolatile magnetic easy-axis rotation in epitaxial ferromagnetic thin films on ferroelectric single crystal substrates Lattice dynamics and elasticity of silver thiogallate ( AgGaS 2 ) from ab initio calculations

The hot embossing of glass with a size on the submicron or micron level is a target of interest for the industrial production of products such as microdevices. For fluidic micro chip applications, polymer materials have been used with the advantage of a relatively low cost of fabrication. However, glass is suitable for high-temperature applications such as in microreactors.Although glass is also a good candidate material for optical devices because of its enhanced optical properties, the development of mold materials has not been established for the hot embossing of glass. In this study, we used Ni-W as a mold material for the hot embossing of glass. A plated Ni-W film has a high heat resistance and a linear expansion coefficient, properties that are similar to those of glass materials. Focused ion beam (FIB) machining was employed for the micron and submicron structurings of a Ni-W mold material. Borosilicate glass, D263, was used as glass material. Glass patterns of 0.4 mm width were obtained by hot embossing with the Ni-W mold.

After a laser annealing experiment on Si wafer, we found an asymmetric sheet resistance on the surface of the wafer. Periodic nano-strip grating lines (nano-SGLs) were self-organized along the trace of one-time scanning of the continuous wave (CW) laser. Depending on laser power, the nano-trench formed with a period ranging from 500 to 800 nm with a flat trough between trench structures. This simple method of combining the scanning laser with high scanning speed of 300 m min(-1) promises a large area of nanostructure fabrication with a high output. As a demonstration of the versatile method, concentric circles were drawn on silicon substrate rotated by a personal computer (PC) cooling fan. Even with such a simple system, the nano-SGL showed iridescence from the concentric circles.

No abstract

We fabricated microlenses and the logo of the National Institute of Advanced Industrial Science and Technology (AIST) on Pyrex glass by employing thermal nanoimprint technology. The mold material used for imprinting on Pyrex glass was an amorphous Ni-P alloy that was deposited on Inconel-600 by electroless plating technology. The complete fabrication technique consisted of highly accurate processing by focused-ion-beam (FIB) on material that involved a high-temperature thermal treatment that has the advantage of improving the hardness of the mold. An amorphous Ni-P alloy layer on an Inconel-600 substrate was characterized by measuring its X-ray diffraction spectrum. Using this technique we successfully developed a low-cost mold for imprinting on Pyrex glass instead of using a more expensive glass-like carbon mold that is commonly used for this purpose. Microlenses with concave curvatures having radii of 12 and 20 mm were created on the mold by a FIB system equipped with three-dimensional computer-aided-design (CAD) software. This mold was used for thermal imprinting on Pyrex glass substrates to fabricate microlenses and the AIST logo. When polished Inconel-600 was used as a substrate for molds, the accuracy of the Ni-P mold proved to be of higher quality than a mold made of unpolished Inconel-600. The microlenses made using Ni-P/ polished-Inconel-600 molds showed lubricious surfaces that were not possible to achieve using Ni-P/unpolished-Inconel-600 molds. Moreover, some of the parameters in Ni-P electroless plating were changed in order to make three kinds of molds with P content ratios of 4, 8, and 16 wt %. The micro-vickers hardness caused by thermal treatment and the differences among the transcript values on Pyrex glass were also evaluated experimentally.