In a continuation of previous studies, the wetting properties of the hydrophobic diureapropyltriethoxysilane [bis(aminopropyl)-terminated polydimethylsiloxane (1000)] (PDMSU) sol-gel hybrid, which forms washing-resistant water-repellent finishes on cotton fabrics, were further investigated. The addition of 1H,1H,2H,2H-perfluorooctyltriethoxysilane (PFOTES) to PDMSU resulted in a highly apolar low-energy surface on aluminum with gammaStotal equal to 14.5 mJ/m2 and a DetlaGiwi value of -82 mJ/m2. Mixed PFOTES-PDMSU finishes applied on cotton fabrics increased the water contact angles (thetaw) from approximately 130 degrees (PDMSU) to 147 degrees, also imparting oleophobicity (thetadiiodomethane=130 degrees, thetan-hexadecane=120 degrees) to the finished cotton fabrics. Washing caused breakage of the coating's integrity as established from SEM, which was attributed to the partial removal of PFOTES from the composite films, also shown by subtractive IR attenuated total reflectance (ATR) and XPS spectral measurements made on washed and unwashed fabrics. The antibacterial properties of the PFOTES-PDMSU-finished fabrics were assessed with the transfer method (EN ISO 20743:2007), revealing that the reduction of Escherichia coli bacteria on unwashed cotton fabrics was nearly 100%. Moreover, for washed (10 times) cotton fabrics a much higher bacterial reduction was noted for the PFOTES-PDMSU finishes (60.6+/-10.8%), surpassing PDMSU (30.4+/-6.1%) and commercial fluoroalkoxysilane (FAS) (21.9+/-5.7%) finishes. The structure of PFOTES-PDMSU gels, xerogels, and the corresponding coatings was investigated by analyzing the 29Si NMR and IR ATR spectra and comparing them with the spectra of PFOTES and octameric (T8) PFOTES based polyhedra. The results revealed the tendency of PFOTES to condense in octameric silsesquioxane polyhedra (T8), coexisting in the PDMSU sol-gel network with cyclic tetramers (T4(OH)4) and open cube-like species (T7(OH)3). The presence of -OH-functionalized PFOTES silsesquioxanes, established even in coatings heat-treated at 140 degrees C (15 min), also explained the excellent washing fastness of PFOTES finishes on cotton fabrics. The regenerative nature of the water- and oil-repellent properties of washed PFOTES-PDMSU-finished cotton fabrics was attributed to the surface mobility of the T8 PFOTES based polyhedra, ousted from the coating interior during consecutive washings.

A mechanism for Li-S battery operation with a composite electrode and an adsorption additive obtained by using operando UV/Vis spectroscopy and X-ray absorption spectroscopy confirms the role of the adsorption additive and reflects the conversion mechanism of sulfur into Li 2 S. Operando UV/Vis spectroscopy shows a reversible appearance of the long-chain polysulfides in the separator in the fifth cycle, whereas the appearance of mid-and short-chain polysulfides suggests a polysulfide shuttle mechanism. By using a non-sulfur-containing electrolyte, a high-precision analysis of sulfur K-edge XANES and EXAFS spectra is possible. The XANES analysis shows that polysulfides reach the maximum concentration at the end of the high-voltage plateau, and the low-voltage plateau is characteristic of the polysulfides/Li 2 S equilibrium. The relative amount of Li 2 S increases linearly until the end of discharge and reaches a relative amount of 75 %. This is confirmed by sulfur K-edge EXAFS analysis. Additionally, a quantitative analysis of EXAFS spectra measured during discharge evidences a decrease of the average S-S coordination number. This can be interpreted as a decrease of the chain length of polysulfides. EXAFS analysis showed that there are no specific interactions of the polysulfide species with the matrix or with other species in the electrolyte.

A novel bifunctional polyhedral oligomeric silsesquioxane (POSS) based silane precursor R(x)R'(y)(SiO(3/2))(8), (x + y = 8), bearing 3-(N-(3-triethoxysilylpropyl)ureido)propyl (ureasil - U) and isooctyl (IO) groups (i.e., U(2)IO(6) POSS) was synthesized, and the corresponding coatings, prepared under the acid hydrolysis conditions, were studied in order to assess their corrosion inhibition of the AA 2024-T3 alloy. The U(2)IO(6) POSS precursor was made in two steps: in the first, an appropriate stoichiometric (2:6) mixture of 3-aminopropyltriethoxysilane (AP(2)) and isooctyltrimethoxysilane (IO(6)) was autoclaved under basic hydrolysis conditions giving AP(2)IO(6)(SiO(3/2))(8) cubes, which were reacted in the second step with 3-isocyanatopropyltriethoxysilane (ICPTES), leading to the bis end-capped sol-gel precursor U(2)IO(6) POSS having a cube-like structure. Coatings were made from sols catalyzed with acidified water. IR and (29)Si NMR spectroscopic studies combined with mass spectrometric measurements were employed to confirm the cube-like structure of AP(2)IO(6) and U(2)IO(6) POSS. The structure and morphology of the U(2)IO(6) POSS coatings were studied with the help of infrared reflection-absorption (IR RA) spectroscopic measurements combined with XPS and AFM measurements, providing information about the formation of partially self-assembled coatings. The degree of corrosion inhibition was assessed from the potentiodynamic measurements showing around 10 times smaller current densities for the coatings only 30-40 nm thick. Ex situ IR RA spectroelectrochemical measurements were performed by consecutive measurements of the IR RA spectra of U(2)IO(6) POSS coatings which were chronocoulometrically charged at different potentials. At potentials more positive than the corrosion potential (E(corr) approximately -0.5 V), the amide I bands shifted, indicating the formation of new urea-urea aggregations and associations, with the newly formed strong band at 1680-1690 cm(-1) suggesting the formation of amidonium ions. These results showed that the urea groups represented the weakest part of the coatings due to their tendency to protonation.

No abstract