No abstract

Workers in the electroplating industry are potentially exposed to a range of hazardous substances including nickel and hexavalent chromium (chromium VI) compounds. These can cause serious health effects, including cancer, asthma and dermatitis. This research aimed to investigate whether repeat biological monitoring (BM) over time could drive sustainable improvements in exposure control in the industry. BM was performed on multiple occasions over 3 years, at 53 electroplating companies in Great Britain. Surface and dermal contamination was also measured, and controls were assessed. Air monitoring was undertaken on repeat visits where previous BM results were of concern. There were significant reductions in urinary nickel and chromium levels over the lifetime of this work in the subset of companies where initially, control deficiencies were more significant. Increased risk awareness following provision of direct feedback to individual workers and targeted advice to companies is likely to have contributed to these reductions. This study has shown that exposures to chromium VI and nickel in the electroplating industry occur via a combination of inhalation, dermal and ingestion routes. Surface contamination found in areas such as canteens highlights the potential for transferral from work areas, and the importance of a regular cleaning regime.

Workplace-related outbreaks of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) continue to occur globally. The manufacturing sector presents a particular concern for outbreaks, and a better understanding of transmission risks are needed. Between 9 March and 24 April 2021, the COVID-19 (coronavirus disease 2019) Outbreak Investigation to Understand Transmission (COVID-OUT) study undertook a comprehensive investigation of a SARS-CoV-2 outbreak at an automotive manufacturing site in England. The site had a total of 266 workers, and 51 SARS-CoV-2 infections. Overall, ventilation, humidity, and temperature at the site were assessed to be appropriate for the number of workers and the work being conducted. The company had implemented a number of infection control procedures, including provision of face coverings, spacing in the work, and welfare areas to allow for social distancing. However, observations of worker practices identified lapses in social distancing, although all were wearing face coverings. A total of 38 workers, including four confirmed cases, participated in the COVID-OUT study. The majority of participants received COVID-19 prevention training, though 42.9% also reported that their work required close physical contact with co-workers. Additionally, 73.7% and 34.2% had concerns regarding reductions in future income and future unemployment, respectively, due to self-isolation. This investigation adds to the growing body of evidence of SARS-CoV-2 outbreaks from the manufacturing sector. Despite a layered COVID-19 control strategy at this site, cases clustered in areas of high occupancy and close worker proximity.

No abstract

The method that is probably the most commonly used worldwide for the determination of total organic isocyanates (NCO) in air is the Health and Safety Executive method, MDHS 25/3, Organic Isocyanates in Air, and its variants. This paper summarizes some of the research and development work carried out by Health and Safety Laboratory on this method since its publication in 1999 with the eventual aim of incorporating this work in an updated version of MDHS 25 (i.e. MDHS 25/4). The work falls into two main areas: use of liquid chromatography/mass spectrometry (LC/MS) as an alternative to liquid chromatography with electrochemical and ultraviolet/visible detection (LC/EC/UV) and evaluation of 'solid-phase' sampling techniques as an alternative to the impinger-filter combination stated in MDHS 25/3. This paper deals primarily with HDI-based NCO but some comments regarding aromatic NCO (MDI and TDI) are included for completeness. An LC/MS/MS version of MDHS 25/3 has been developed that gives improved performance to the 'classical' version of MDHS 25/3 using EC/UV detection. The LC/MS/MS offers significant advantages over the EC/UV version of MDHS 25/3 in that it is more sensitive, provides improved identification, and has been found to be easier to use. The solid-phase samplers evaluated were a double-thickness glass-fibre (GF/B) filter coated with 1-(2-methoxyphenyl)piperazine (MP) reagent in an IOM (Institute of Occupational Medicine) sampling head ('FIN-MP' sampler) and an MP-impregnated polyurethane foam sponge (PUF) with an MP-coated glass-fibre (GF/A) backup filter also in an IOM sampling head ('Rudzinski' sampler). Both samplers were found to give acceptable performance for the sampling of oligomeric HDI in workplace air and in laboratory simulations when compared to the impinger-filter combination at levels corresponding to the UK short-term limit (70 μg m(-3)). For practical reasons, the FIN-MP sampler was the preferred alternative.