Powered exoskeletons can empower paraplegics to stand and walk. Actively controlled hip ab/adduction (HAA) is needed for weight shift and for lateral foot placement to support dynamic balance control and to counteract disturbances in the frontal plane. Here, we describe the design, control, and preliminary evaluation of a novel exoskeleton, MINDWALKER. Besides powered hip flexion/extension and knee flexion/extension, it also has powered HAA. Each of the powered joints has a series elastic actuator, which can deliver 100 Nm torque and 1 kW power. A finite-state machine based controller provides gait assistance in both the sagittal and frontal planes. State transitions, such as stepping, can be triggered by the displacement of the Center of Mass (CoM). A novel step-width adaptation algorithm was proposed to stabilize lateral balance. We tested this exoskeleton on both healthy subjects and paraplegics. Experimental results showed that all users could successfully trigger steps by CoM displacement. The step-width adaptation algorithm could actively counteract disturbances, such as pushes. With the current implementations, stable walking without crutches has been achieved for healthy subjects but not yet for SCI paraplegics. More research and development is needed to improve the gait stability.

Neuroprosthetic technology and robotic exoskeletons are being developed to facilitate stepping, reduce muscle efforts, and promote motor recovery. Nevertheless, the guidance forces of an exoskeleton may influence the sensory inputs, sensorimotor interactions and resulting muscle activity patterns during stepping. The aim of this study was to report the muscle activation patterns in a sample of intact and injured subjects while walking with a robotic exoskeleton and, in particular, to quantify the level of muscle activity during assisted gait. We recorded electromyographic (EMG) activity of different leg and arm muscles during overground walking in an exoskeleton in six healthy individuals and four spinal cord injury (SCI) participants. In SCI patients, EMG activity of the upper limb muscles was augmented while activation of leg muscles was typically small. Contrary to our expectations, however, in neurologically intact subjects, EMG activity of leg muscles was similar or even larger during exoskeleton-assisted walking compared to normal overground walking. In addition, significant variations in the EMG waveforms were found across different walking conditions. The most variable pattern was observed in the hamstring muscles. Overall, the results are consistent with a non-linear reorganization of the locomotor output when using the robotic stepping devices. The findings may contribute to our understanding of human-machine interactions and adaptation of locomotor activity patterns.

This paper presents MINDWALKER, which is an ambitious EC funded research project coordinated by Space Applications Services aiming at the development of novel Brain Neural Computer Interfaces (BNCI) and robotics technologies, with the goal of obtaining a crutch-less assistive lower limbs exoskeleton, with non-invasive brain control approach as main strategy. Complementary BNCI control approaches such as arms electromyograms (EMG) are also researched. In the last phase of the project, the developed system should undergo a clinical evaluation with Spinal Cord Injured (SCI) subjects at the Fondazione Santa Lucia, Italy. I. INTRODUCTION INDWALKWER [1] is funded by EC under an ICT research programme named e-Inclusion, that aims at improving inclusion in social life of European individuals, in particular those with reduced mobility (due to e.g. disability).The research question that initiated this project can be stated following this way: could a lower limbs assistive exoskeleton system allow SCI subjects to recover mobility, relying on convenient, non-invasive BNCI control signals acquisition -EEG based as far as possible, and without the need for stability improvement accessories such as crutches (that cannot be used by quadriplegic subjects, and that prevent paraplegic subjects from using their arms and hands Manuscript received April 30 th , 2012. MINDWALKER is supported in part by the European Commission through the FP7 Programme, with project reference ICT-2009-247959 (Health, e-Inclusion). MINDWALKER is member of the Future BNCI European network.

No abstract

The capabilities of maximising standard payload modules' functionalities for applications such as on-orbit satellite servicing or planetary exploration depend critically on the creation and availability of a standard interface (IF). Standard interface should provide, aside from the necessary mechanical interconnections, electrical power and data connections, as well as thermal transfer between "building block" payload modules. The overall flexibility enabled by such IF will allow endless reconfigurations of payload and other modules for different functional requirements. This can be considered a game changer technology, enabling transformation from the current approach to space missions, deploying single-use system with preplanned and limited functionalities, to a radically new approach with multi-use, dynamically reconfigurable and multifunctional systems. Hence, SIROM aims to set a new research agenda for future affordable space missions. Within this context, the partners of the SIROM (Standard Interface for Robotic Manipulation of payloads in future space missions) project are developing the first standard IF solution that combines the four required functionalities in an integrated and compact form for future space missions. With a mass lower than 1.5 kg and having an external diameter of 120 mm and a height of 30 mm, this novel interface permits not only mechanical coupling but also electrical, data and thermal connectivity between so called Active Payload Modules (APMs), as well as other modules such as the robotic end-effectors. This multi-functional IF features an androgynous design to allow for replacement and reconfiguration of the individual modules in any combination desired. It consists of the following sub-assemblies: mechanical IF, electrical IF, data IF, thermal IF and IF controller. A clear advantage of SIROM design is that its mechanical IF consists of a latching and guiding systems for misalignment correction, capable of withstanding certain robotic arm positioning inaccuracies: ± 5 mm translation and ± 1.5°rotation in all axes. Regarding the electrical and data IFs, SIROM transfers up to 150 W electrical power and provides a data transfer rate of 100 Mbit/s via SpaceWire, plus command communication with speeds up to 1Mbit/s via CAN bus. The thermal IF provides fluidic ports for flow transfer and has the potential to transfer 2500 W between APMs accordingly provided with the corresponding close-loop heat exchange system. Although not envisaged for SIROM current design, a possible variation could be to use these ports for satellite re-fuelling. Apart from that, SIROM exhibits redundant coupling capabilities: it can match and couple another completely passive SIROM. It is provided with main and redundant connectors for thermal, electrical, data and control flow in case of one of the lines fails. All in all, SIROM will enable long duration missions with no logistic support, refurbishing, maintenance and reconfiguration of satellites, cost efficiency and simplification of the tool exchange in scient...