While the characteristics of the driven translocation for asymptotically long polymers are well understood, this is not the case for finite-sized polymers, which are relevant for real-world experiments and simulation studies. Most notably, the behavior of the exponent α, which describes the scaling of the translocation time with polymer length, when the driving force fp in the pore is changed, is under debate. By Langevin dynamics simulations of regular and modified translocation models using the freely jointed-chain polymer model we find that a previously reported incomplete model, where the trans side and fluctuations were excluded, gives rise to characteristics that are in stark contradiction with those of the complete model, for which α increases with fp. Our results suggest that contribution due to fluctuations is important. We construct a minimal model where dynamics is completely excluded to show that close alignment with a full translocation model can be achieved. Our findings set very stringent requirements for a minimal model that is supposed to describe the driven polymer translocation correctly.

Motivated by identifying the origin of the bias dependence of tension propagation, we investigate methods for measuring tension propagation quantitatively in computer simulations of driven polymer translocation. Here, the motion of flexible polymer chains through a narrow pore is simulated using Langevin dynamics. We measure tension forces, bead velocities, bead distances, and bond angles along the polymer at all stages of translocation with unprecedented precision. Measurements are done at a standard temperature used in simulations and at zero temperature to pin down the effect of fluctuations. The measured quantities were found to give qualitatively similar characteristics, but the bias dependence could be determined only using tension force. We find that in the scaling relation τ∼N^{β}f_{d}^{α} for translocation time τ, the polymer length N, and the bias force f_{d}, the increase of the exponent β with bias is caused by center-of-mass diffusion of the polymer toward the pore on the cis side. We find that this diffusion also causes the exponent α to deviate from the ideal value -1. The bias dependence of β was found to result from combination of diffusion and pore friction and so be relevant for polymers that are too short to be considered asymptotically long. The effect is relevant in experiments all of which are made using polymers whose lengths are far below the asymptotic limit. Thereby, our results also corroborate the theoretical prediction by Sakaue's theory [Polymers 8, 424 (2016)2073-436010.3390/polym8120424] that there should not be bias dependence of β for asymptotically long polymers. By excluding fluctuations we also show that monomer crowding at the pore exit cannot have a measurable effect on translocation dynamics under realistic conditions.

We study translocation of semiflexible polymers driven by force f_{d} inside a nanometer-scale pore using our three-dimensional Langevin dynamics model. We show that the translocation time τ increases with increasing bending rigidity κ. Similarly, the exponent β for the scaling of τ with polymer length N,τ∼N^{β}, increases with increasing κ as well as with increasing f_{d}. By comparing waiting times between semiflexible and fully flexible polymers we show that for realistic f_{d} translocation dynamics is to a large extent, but not completely, determined by the polymer's elastic length measured in number of Kuhn segments N_{Kuhn}. Unlike in driven translocation of flexible polymers, friction related to the polymer segment on the trans side has a considerable effect on the resulting dynamics. This friction is intermittently reduced by buckling of the polymer segment in the vicinity of the pore opening on the trans side. We show that in the experimentally relevant regime where viscosity is higher than in computer simulation models, the probability for this buckling increases with increasing f_{d}, giving rise to a larger contribution to the trans side friction at small f_{d}. Similarly to flexible polymers, we find significant center-of-mass diffusion of the cis side polymer segment which speeds up translocation. This effect is larger for smaller f_{d}. However, this speedup is smaller than the slowing down due to the trans side friction. At large enough N_{Kuhn}, the roles can be seen to be reversed, and the dynamics of flexible polymers can be reached. However, for example, polymers used in translocation experiments of DNA are elastically so short that the finite-length dynamics outlined here applies.

Polymer ejection from a capsid through a nanoscale pore is an important biological process with relevance to modern biotechnology. Here, we study generic capsid ejection using Langevin dynamics. We show that even when the ejection takes place within the drift-dominated region there is a very high probability for the ejection process not to be completed. Introducing a small aligning force at the pore entrance enhances ejection dramatically. Such a pore asymmetry is a candidate for a mechanism by which viral ejection is completed. By detailed high-resolution simulations we show that such capsid ejection is an out-of-equilibrium process that shares many common features with the much studied driven polymer translocation through a pore in a wall or a membrane. We find that the ejection times scale with polymer length, τ ∼ N α . We show that for the pore without the asymmetry the previous predictions corroborated by Monte Carlo simulations do not hold. For the pore with the asymmetry the scaling exponent varies with the initial monomer density (monomers per capsid volume) ρ inside the capsid. For very low densities ρ 0.002 the polymer is only weakly confined by the capsid, and we measure α = 1.33, which is close to α = 1.4 obtained for polymer translocation. At intermediate densities the scaling exponents α = 1.25 and 1.21 for ρ = 0.01 and 0.02, respectively. These scalings are in accord with a crude derivation for the lower limit α = 1.2. For the asymmetrical pore precise scaling breaks down, when the density exceeds the value for complete confinement by the capsid, ρ 0.25. The high-resolution data show that the capsid ejection for both pores, analogously to polymer translocation, can be characterized as a multiplicative stochastic process that is dominated by small-scale transitions.

We use stochastic rotation dynamics to examine the dynamics of the ejection of an initially strongly confined flexible polymer from a spherical capsid with and without hydrodynamics. The results obtained using SRD are compared to similar Langevin simulations. Inclusion of hydrodynamic modes speeds up the ejection but also allows the part of the polymer outside the capsid to expand closer to equilibrium. This shows as higher values of radius of gyration when hydrodynamics are enabled. By examining the waiting times of individual polymer beads we find that the waiting time tw grows with the number of ejected monomers s as a sum of two exponents. When ≈ 63% of the polymer has ejected the ejection enters the regime of slower dynamics. The functional form of tw vs s is universal for all ejection processes starting from the same initial monomer densities. Inclusion of hydrodynamics only reduces its magnitude. Consequently, we define a universal scaling function h such that the cumulative waiting time t = N0h(s/N0) for large N0. Our unprecedently precise measurements of force indicate that this form for tw(s) originates from the corresponding force towards the pore decreasing super exponentially at the end of the ejection. Our measured tw(s) explains the apparent superlinear scaling of the ejection time with the polymer length for short polymers. However, for asymptotically long polymers tw(s) predicts linear scaling.